Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
which app should I use when I want to do LL BQB test with harmony on nRF52840?
it can not connected with harmony when I use DTM project. It seems the interface of nRF52840...
Dear nordic,
I am currently working with nRf52840. For designing antenna is there any role for dielectric layer thickness and conductive copper layer thickness
Hi all, I'm testing quick connections and communications using multilink(nus). I am using multilink central example in nrf52832(Central : softdevice v2.0.0 & SDK v11, Peripheral...
I am trying to measure the power consumption when transmitting data from an external device to nRF 52832 to a smartphone.
I am trying to measure the power consumption of...
Dear, I'm designing a PCB with nRF52832 and I will intend to use DCDC converter therefore I putted the two inductors (10uH and 15nH) between DCC and DEC4 pins. The same hardware...
Hi,
I am developing a project in IAR Embedded Workbench for nRF52840-Preview-DK. I have integrated different modules (ble, ADC, SPI, I2C) in this project. I don't have...
I like to integrate the nRF54XXX with a LNA/PA combo (skyworks RFX2401C or 66110). Could you please tell me which pin should be used to control the RFX2401C TX/RX? Which has...
Hello all,
I am currently working on a project to control a door lock and use ble_app_multirole_lesc as reference.
As measurement the current consumption is around 6.5mA...
Hi, I’m working on low power wireless sensor network. I have a big dilemma in choose of wireless mesh solution. Maybe firstly, what i need: 1. Support for low power devices...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
Hi,
I am trying to connect to a device while service discovery for another device is running, this is needed to go through connecting multiple devices as fast as possible...
Hi
I am using the light controller and added zb_nlme_permit_joining_request to allowing devices to join the network.
I get a good ZB_ZDO_SIGNAL_DEVICE_ANNCE signal and...