Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I tried to add ble_nus service to buttonless app (sdk 14).
Keil doen't raise any errors and compiled project, but app is not work actuall in NRF_LOG I can see these messages...
Hello,
I'm confused regarding the nRF82840 matching network found in the datasheet and dev kit. Is the Pi-filter composed of C3-L1-C4 the 50ohm matching network or should...
Hi,
I have a Rigado BDM-300 (nRF52832) on a small custom board.
Using SDK 13.1 with SD132 v4.0.2.
I've taken a template project and adjusted it to my needs. I can get...
Not sure if there is already a worked-out example of converting analog to digital data from AIN0 and then updating a characteristic with that data.
I've worked through...
Hello ,
I am using examples\ble_central\ble_app_uart_c\pca10031\s120 in the SDK 10.00 .
I know that s120 supports up to 8 peripherals. I am using NRF51 Dongle as a Central...
hello everyone:
i use nrf51822QFAC(with 256kb flash and 32kb ram).The project is this "SDK12.3-ANCS\examples\ble_peripheral\ble_app_ancs_c\pca10028\s130\arm5_no_packs"...
Hi all,
I have a board with old code, it has a bootloader + sofdevice 110 + application all from SDK7 and I want to upgrade it via serial single bank DFU, to the SDK11...
I've developed a PCB containing the nRF51822. I am trying to uploaded the example program "ble_app_uart_s110_pca10028" to it, but the chip is not broadcasting (so I assume...
I use buttonless_dfu app from sdk 14
Generate settings file by nrfutil
Merge with bootloader hex file
Erase chip, flash SD, flash bootloader (everything use nrfutil...
Hi,
I am using SDK 12.2.0 with secure DFU service.i want to use pwm in my code.And i init pwm with APP_PWM_INSTANCE(PWM1,1),then i get an error:identifier "TIMER0_ENABLED...
I have built a custom board that is identical in schematic to the nRF52 DK board, with some additional circuitry connected as a SPI interface to the nRF chip. The MCU is the...
Hi,
Glad to see Nordic just released a new alpha version SDK yesterday!
I am wondering when you will release the mesh friend nodes support SDK? I mean support those low...
Hi,
I need you suggestion / information about Nordic chip. We currently have nRF52 (nRF52832) chip. However, in our application we will be using Nordic beacons as an transmitter...
Hello All,
I've finally managed to get Eclipse up and running after migrating from Keil, but now I'm having the following problem: I'm trying to port the buttonless_dfu...
