after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
Using nRF51DK with softdevice 8.0 and sdk8.
I found the max number of whitelist in "ble_gap.h"...
/**@brief Maximum amount of addresses in a whitelist. */
#define...
Hi
I want to get the number of broadcast data.i try it as follow:
But i can not get the BLE_EVT_TX_COMPLETE event. Why? can you tell how to get the number of broadcast...
Searched -- without success -- the SDK docs extensively for access to the Transmit Window Size.
Wondering if there are ways we can manipulate it, and query the current...
Hi all,
I want to know how long it takes for NRF24LE1 to wake up from low power mode, especially in these situations:
1) Wakeup from pin voltage level , from Register...
Hi~
I am trying the example code of [--app-button-example-master--] from here... github.com/.../nrf51-app-button-example
for understanding button press features. I did...
Here i have made an UART0_IRQHandler routine. When i try to send some 50 bytes data through UART using PC tool here its receiving bytes, but it only receives 1st 6 bytes which...
Hi Everyone,
I'm working on adding DFU on my project and here is my setup:
Softdevice = 7.1.0
SDK = 6.1.0
DFU Bootloader = Keil compiled from SDK 6.1.0
MCP...
I'm having a bit of confusion understanding how the nRF51 Series Compatibility Matrix works.
I have a QFACA10 development board running my software perfectly, but when...
The nRF51822 Bluetooth Smart Beacon Kit User Guide (nRF51822-BK-UG) mentions an iOS project contained in the zip file nRFBeacons_iOS.zip. Where is this file? I cannot find...
Hello all,
I'm trying to save the service context with the Device Manager on the Central side. But I don't understand the implementation on how to do this. But no information...
I'm trying to adapt the BLE_BAS_C library to perform discovery and read/write operations for a custom service. However, when I change the UUID that I register with ble_db_discovery_evt_register...
i used this function to send data to my ble device ble_nus_string_send.this function sends ASCII values. and when i pass this function hex values it converts them into ascii...
Hello,
I was using wiringPiSPI() to connect via SPI and so i was using wiringPiISR function to create an interupt handler that will do callback to the user suplied function...
I'm compiling my project successfully in Eclipse, but trying to build it from the command line (cygwin) fails near the end with this error (make, make all, make nrf51422_xxac_s110...
