Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
use s130-0.5.0
A1 connect B1 with BLE_GAP_ADV_TYPE_ADV_DIRECT_IND, after this, A1 is slave, B1 is master,A1 can't send any type advertisement
use s130-1.0.0
A1...
Good afternoon,
I have developed a custom board based on nRF51822 device and SD-110-v8. For debugging I have been usign the Ulink2 tool with Keil. Now, I want to implement...
This is not working for me. My goal is to use printf() in my code. I follow the steps outlined in this link
..including calling initialise_monitor_handles(); before calling...
I was able to measure current with the test probes I have. However, I really liked the idea of test probes that were like the ones in the drawing below. I have not seen test...
I am using the PWM library in this repository for a nRF51822. I write the following code to generate a ~ 30% dutycycle 500 kHz PWM output:
#define V_CLK 5
static void...
Hello,
I am using Timer_2 with two CC registers configured, 2 PPI channels (one for each CC register in the timer), and one GPTIO_TE to make a PWM to control dimming on...
hi,
my nrf51822dk was downloaded s110 hrs demo,and it was advertising,i used a ble sniffer dongle to get the advertising data.the AdvData is "0B 09 4E 6F 72 64 69 63 5F 48...
Why is it a standard in nordic-supplied code to initialize structs with memset like so? An example would be:
ble_gatts_char_md_t char_md;
memset(&char_md, 0, sizeof(char_md...
//Edit:
So Hung Bui just told me in another question, that there is indeed a buffer of size 6 or so?
How can I decrease that to 1 (i.e. disable it) so that only the latest...
I have the nRF52 DK and cannot determine the silicon revision on it. Is it the 'Engineering A' revision and therefore is subject to all the Errata that is currently published...
there are 3 modules to test(A1,B1,C1)
*2. A1 connect with B1(B1 is master, A1 is slave), C1 is power off, B1 as slave attempt to connect C1 with BLE_GAP_ADV_TYPE_ADV_IND...
I need a PWM signal as outoput from the nRF51-DK. And I do need the softdevice. So I decided to pick the code from the nrf51-pwm-library-master and add it to my project(SKD...
