Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Nordic will release a new development kit in april, named mkit.
It is based on arm mbed .
Writing a ble app will be easy, fast and simple using mbed BLE API .
My question...
Hello,
I compiled the pc10001/blinky_example with gcc/makefile, i can flash it with nRFgo Studio and it works. But if I try to compile/flash the pc10001/button_radio_example...
My computer is running KEIL MDK4 and nRF51 SDK4.
So far no problem with nRF51422QFAAC0.
Upgrading to Keil MDK5 would be a nightmare, so that I gave up after a few days...
Hi,
I'm trying the nRF UART example but I can't get it to work.
I have opened the uart_example project in uVision and loaded it to PCA10001.
Then I opened the Master...
I want to add timer to send sensor movement data to PC every 8ms(125HZ).
But when I add app_timer like normal
1.raise APP_TIMER_MAX_TIMERS
2.raise APP_TIMER_OP_QUEUE_SIZE...
I am testing Keil MDK5 and created my own simple nRF51422 project (not from the sample), hello world type of code. But the "download" button is disabled.
The J-Link is configured...
Hi,
Can anyone please tell me the exact way to enter into the bootloader mode by writing some characteristics with specific value.
I tried setting
NRF_POWER->GPREGRET...
The existing Master Control Panel cannot be used as an automatic test platform.
Basically I am looking to send commands via a tcp/ip which will invoke scan/connect/disconnect...
I'm trying to measure a scaled down battery voltage level on an ADC pin. Given my resistor values the voltage on the pin should be about 0.279 times VBATT, to fit within 1...
Hi Nordic guys,
How much is the current consumption of the LDO only (quiescent current), without DC / DC converter, in uA? How much is dropout voltage and PSRR (ripple...
I try to modify "ble_app_ibeacon" sample code. But when I add some adv_uuids for services to advdata.uuids_complete or I changed advdata.name_type from BLE_ADVDATA_NO_NAME...
Hi,
I need to write a validation document for nRF51822 . The first step need is the specification for its calibration. But I couldn't find it in your website. Can you send...
Hello,
My project name is Remote Operated Vehicle. Basically i am using a PS2 controller as the joystick to control the car. So, my aim is to build wireless interface between...
