Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hi,
I'm developing my app on nRF52840, NCS2.7.0 on VS Code 1.100.0.
My application needs to save settings data (4 x int32_t ) to external the NOR Flash (mx25r64) in `settings_storage...
Hello,
nRF Connect SDK v3.0.1 nRF54L15-DK v0.9.1
Currently, I’m exploring whether it’s possible to create a Bluetooth application that can be controlled from an external...
Hi,
I am using nrf54l15 ,here I have bare i2s code for reading data from mics and ble code for notifying that data but here I am planning to use lc3 codec to compress data...
I have just purchased nRF54L15 DK, run Quick Start and programmed 'Hello World', but the verification failed and nothing happened. I opened the serial terminal, but nothing...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
I'm following the tutorial Exercise 1 – Custom board for single-core SoC using ncs v2.9.0 with one slight difference in that I'm using a nRF52DK with nRF52832 because that...
Hello,
I am running firmware on a custom board toting an nrf5340 with NCS version 2.3.0. There is also a Micron 8Gb NAND flash on board that I have a custom driver for....
Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
Hello~ I used the ot-nrf528xx codebase for compilation, and according to the content in the readme, I compiled two Hex files for USB and SPI interfaces using the USB_trans...
Hi, the nordic team
I am working on thread protocol using SDK version 2.9.1.
I use the SED device,My poll is 1000 ms. How can I receive messages from my parent node when...
Hi,
I am power profiling an application on the NRF52 DK. The application uses SPI to communicate with the BMA400 accelerometer:
The program initializes the accelerometer...
Dear support team,
I am getting an error while performing DFU using nRF Connect.
My SDK version is 2.4.2, I need to do DFU using BLE simultaneously, for that i tried...
