Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
Hi
I run nRF connect SDK 1.7.1 and have a custom nRF9160 board.
I'm trying to get the I2C peripheral to work with my own hardware.
I have read and googled all tutorials...
Hi,
Can I use the hex file compiled for nRF52810 for nRF52805 directly ? Please note that I am not using any peripherals other than radio.
Can I use the nRF52810 build...
We use the nRF24L01+ in a dedicated RX mode, and it is preceded by a power splitter, filters and LNA. In order to run some system calculations, I'd really like to know the...
We are using nRF52840 on a custom board with nRF5 SDK v15.3.0.
Our application uses the NFCT driver (nrfx_nfct) along with nfc_t2t_lib_gcc.a to emulate a NFC tag with some...
HI,Therd:
I used the mesh sdk 5.0.0(BLE SDK 17.0.2), and run the example light_switch_server_nrf52832_xxAA_s132_7_2_0.emProject. when i use the nRF Mesh app on the phone...
Hi,
I am evaluating nRF53 for ZigBee in a Linux application that implements a MQTT-SN Gateway. I am interested in learning about Linux board can connect to the nRF53 (USB...
using nRF5 SDK 17.1.0
Segger
I need some understanding of the QDEC. if I connect a motor that has a A/B output at a 5KHZ rate.
what is the maximum rate at which the...
Hi,
We are trying to change the name of our BLE device of our solution with being always different for each device. The device name would be like a serial number that is...
SDK: 7.0.2
CHIP: nRF52840
I'm faced with strange dfu behavior.
The dfu SD+BL+APP (softdevice 6.1.1 -> 7.2.0) is working fine which was flashed by j-link.
However...
Hi,my project is going on with nrf5340dk,i use the codec tlv320aic3109 to record audio data.i have the linux driver about this IC，but i haven't familar linux driver.could...
Hi,
I am trying to utilize the nRF Thread Topology Monitor with the CLI example from nRF Connect SDK, but it does not seem to work. " Error - No response from Thread CLI...
Hi,
Want to know more about NV memory interface
Do we have implementation in Nordic SDK for to keep the data stored into the memory
Please share the code path if we...
Hi,
Yesterday I received the nRF5340-DK. I started following the 'Get started' procedure on the product page. The LEDs start pulsating and pressing the buttons lights up...
Hi,
I have some issue in developing APP for devices based on NRF51822. They have been developed in 2016 with an old bootloader, when there was no use of zip pack. We usually...
My project uses nRF52832 and I'm at the point of the project where I'm trying to minimize power consumption.
To assist in this, I created a very small main() that goes through...
