Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
I want to control the connection to send data for about 100ms, but the service discovery process takes about 300ms. When the service characteristics are known, I want to inform...
Hi, our application uses a nrf52840 module and a nrf52840 dongle. ( sdk15.0.0) in the application.
The central sends data to the peripheral continuously on an event. When...
I am trying to do some power measurements on the nRF5340 using the power profiler.
As suggested in the guide here, I am removing serial support to reduce power consumption...
Provide your AWS credentials page for Asset Tracker Cloud Example for AWS mentions sub-accounts. There is absolutely no such thing as a sub-account in AWS. The page is totally...
Hi.
I've been working with the nRF52840 for a couple of months. I started working on SEGGER IDE, but I've found that it was quite difficult to understand the behavior of...
I played around with the SAADC sampling A4 pin. When I connect to GND, I see negative values sometimes. If I connect to 3.3V I see value 235/236 which is, what I expect. ...
I have 2 device gateway and nrf52840 board.
Can i get zigbee distance?? I think RSSI data is possible. Right??
If you can measure the distance between gateway and nrf52840...
Hello,
I am using nRF52833, nRF Connect SDK v1.4.2.
I have imported the Zigbee light switch, light bulb, network_coordinator build and test it successfully.
I have also...
I should not be asking this question here but it should be documented! SoftDevice s130.
A possible error I can get when executing sd_mutex_acquire() is NRF_ERROR_SOC_MUTEX_ALREADY_TAKEN...
Hi All,
Hardware: Custom Board (Buttonless)
SDK : 17.0.2
SD: 7.2.0
Support required: DFU Buttonless
We are able to successfully load and run the DFU buttonless...
I am using nRF52832.
Can I use NFC1/P0.09 as SCL and NFC2/P0.10 as SDA?
nRF52832_PS_v1.4.pdf states "The pin capacitance will be higher on these pins" in 4.3.2.
I am...
I posted one question in my earlier ticket about download firmware to our own device (nRF9160) through DK of NRF9160.
Now we are design the schematic of our own device with...
Dear Concern,
I am getting MCUboot build errors as shown in the below.
C:\Nordic\v1.5.0>west build -b nrf5340dk_nrf5340_cpuapp -d build_mcuboot bootloader/mcuboot...
Hi,
I have nrF52840 DK rev 2.0.1
switch to VDD, Default, SB40 is cut (confirmed by multimeter)
I have the PPK rev 1.1.1
switch DUT to DK
switch Power to DK
I...
Hi,
is possible use for DFU process as DFU server other device as development kit?
I will use it in street lighting but it not usable with development kit. I would use...
