after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip ...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
• nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip • nRF...
Hi,
I have been working through the examples for DFU with the nrf52832 dev kits from the SDK (nRF5_SDK_15.0.0_a53641a) from this folder:
...\nRF5_SDK_15.0.0_a53641a\examples...
Hi, Guys, I have problem with my nRF51822. I built the ble_app_uart project in the SDK v6 and and flashed it on the mcu using j-link and I also flashed S110 SoftDevice version...
Hi Sirs:
I've searched 52840 specifications and devzone, but there is no related information about the maximum external flash size could be adopted on 52840.
Would you...
I'm attempting to use PPI and Timer2 on the NRF52810 to count the clock pulses coming out of the SPIM driver. As there is no way to do this internally (as far as I know) I...
Hi,
I'm using a nrf52 as pheripheral BLE in embedded system with sensors. I need a ble central to receive the data from the sensors by connecting to the nrf52. I'm trying...
Hello, i am trying to store a lot of informations in the flash in order to do this i separated my data in several arrays. I want to store all my arrays in with the same file_ID...
In our project, two RF modules (with nRF24L01+ IC) are used in communicating data. If there is no WiFi around, the two RF modules can communicate very well without packet...
Hi everyone,
I found this example in the SDK for the nRF52840 Dongle: nRF5_SDK_15.0.0_a53641a\examples\connectivity\ble_connectivity\pca10059\ser_s140_usb_hci.
With this...
Dear Sr.,
Can't detect carrier
They are two PCB one TX Carrier and other mush Detect the carrier ---------------------------------------------------------------------...
mains.c
Hello Everyone,
I have deveLoped the Custom PCB whixh has the push button which is connected to VCC so i would like verify my software logic for button configuration...
Hi,
We have a new product based on the NRF52840. We are trying to add NFC record text to the firmware that based on SDK15. We could get the NFC record text from the NRF52840...
We're evaluating the nrf52840 and I am looking at the SPIM peripheral. The datasheet states the following:
"If several AHB bus masters try to access the same AHB slave at...
