Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
In an effort to try and determine why FreeRTOS tickles idle is consuming more current than tick mode with an idle task, see this post devzone.nordicsemi.com/.../ , I noticed...
Hi, i am designing a board using nrf51822 and planning to use a MOSFET for reverse battery protection instead of a schottky diode or a normal diode. I am new to this and learning...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I'm developing a nRF52 application that exploits two ADC channels in single ended configuration.
VDD is 3.0V.
For the signal conditioning I've chosen a driving Op...
I've been trying to get my head around using a BLE central and making connections so I've loaded up the multi-central example to figure out just how everything works. I turned...
Hi everybody!
I am working with ANCS (nrf51822 SDK 9.0) I am confusing on setting the connection parameters which are MIN an MAX connection interval.
Firstly, I set...
Hello,
I have some characteristics on my device that are containing some configuration data.
Every single variable is a global variable.
The values can also be changed...
I am using the nRF51822 bluetooth low energy smart beacon kit and am running into trouble using the GPIOs available on the board (pins 0, 1, 2, 3, 5, 9, 11, 20, 21, 24). For...
Hello Everyone,
I am trying to monitor my battery voltage on the analog pin (ADC) so inorder to do that i am going to use the voltage divider circuit to calcualte the R1...
Hi,
We are working on a smart lock project with nrf51822 third party module with an antenna on pcb.
We are trying to cover 50 cm range at -20 dbm. But even at -30 dbm...
I have created a library for HD44780 Hitachi LCD, and I can transmit data to the LCD through an IO Expander without any problem over TWI lines. Right now I am not using any...
Hi,
I'm learing how to use the NRF51 DK and I'm trying to modify the app GPIOTE example including the uart functionality.
I insert in GPIOTE the directive:
#include ...
Hello,
I try to add battery service in ble_app_uart , but it has some problem.
The Problem is that I can see the Battery service on the phone , but it doesn't change...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
