after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use nrf51422 and integrated BMA250E for Pedometer,
Now I can count the step but I dont how to calculate the speed, cadence and stride length like below
static void...
Hi All,
From my firmware I need to send large ble packets say of 1 K to the phone.
Is there any library or example code for sending large packets. Currently I am splitting...
Hi,
Our application requires that we connect a nRF52832 to a Microchip PIC32MZ host via the Nordic parts UART (RS-232 at CMOS levels).
In a previous application, we...
Hi everyone,
I've been testing SPIM with easyDMA, using nrf_drv_spi. I'd like to flush a 6-axis sensor FIFO in one SPI operation (31 samples * 12 bytes = 372 bytes) but...
Hi,
I am working with the ble_app_uart (central and peripheral) example and they already run fine. Now I discovered that some button actions are already defined on the...
Hello,
I have created the simple software usign NRF51DK to make the led blink for 5 times by using while loop
just to make the other part of my software
my aim of this...
hi，i have a question.
i set the advertise type to BLE_GAP_ADV_TYPE_ADV_NONCONN_IND MODE, and i add scan response data,but i can't see scan response data.Why?
Hi,
I would like to connect nrf8001 to a Renesas microcontroller but I could not find any documentation on how to proceed with this step. The only documentation I could...
The ADC module requires that the output impedance of the connected voltage source be 1kohm or less (section 31.1.3 of RM).
Does the same restriction apply for the LPCOMP...
Im having some issues with my nrf52 DK board, the jLink firmware seems to be buggy, I installed the latest available (160212) manually, but the j-link tool keeps bugging me...
SDK 9.0.0 sd s110
I want bootloader to store some persistent data at the APP DATA location. while going through the bootloader(dual_bank_ble_s110) source code, i noticed...
I have never worked with BLE devices before. Now I have a BLE project where I must be able to do he following:
I want to be able to pair/bond my BLE device to a smartphone...
