Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi.
I'm using PCA10028 as central, SDK10.0.0, S130 V1.0.0.
I can discover 180A UUID and characteristic UUIDs which pripheral device provides such as 0x2a29, 0x2a24, 0x2a26...
my project use s110 8.0.0;I'm using nRF51422_xxAC.
And my project have 7 services.all the Characteristics is 81.
But after I had add 23 Characteristics ,I can't add...
Hi.
I'm trying to get 128bit service uuid as referring to "ble_app_hrs_c" source code.(S130)
And my test peripheral device provides GAP, DEVICE Information and User service...
Hi
I've detected that when using the NRF51822 under Eclipse and GCC compilers, global variables are not automatically initialized. This is because an error on the startup...
I am having some issues figuring out how to send a simple string or character to my central.
What I want is the peripheral to send an acknowledgement back to the central...
Hi,
I want profile / Log the events occurring in my board and save them on to flash. Unfortunately when ever my nRF51822 goes to sleep and wakes up again APP_Timer which...
Dear nordic guys, I'm developing with nrf51822.
I have one simple question.
My customer LG electronics wants to get the nrf master control pannel android app source code...
Hi
I am trying to modify my application so that it uses the latest version of softdevice (v2.0.0-8.alpha) instead of the current one I am using (v2.0.0-7.alpha). My application...
SDK: nRF5_SDK_11.0.0-2.alpha_bc3f6a0
Chip: NRF52
If I perform a TXTX transfer using the twi driver, it sends a repeated start/stop bit in between the two transmits. Is...
Hei,
I would like to compile ble_app_template example which is located in nRF5_SDK_v11 library. I get the following warning "Could not create/access path '._build' !" when...
Hi,
I'm using a timer to send message over uart.
Here is the initialization code:
err_code = app_timer_create(&m_uart_timeout_timer, APP_TIMER_MODE_SINGLE_SHOT, uart_timeout_handler...
I'm hoping this is just something silly that I've overlooked, but I'm running into an issue: Whenever I try to prompt the scheduling of a TWI transaction an error occurs ...
im using sdk10 softdevice 8.0.
on my app I configured #define APP_ADV_INTERVAL 1500 and I noticed that when I activate Dfu service (activate notification on last service...
hello,
I am trying to direct advertisement on NRF51822 board.When giving the peer address i am confused that how to specify the address type of the device, whether BLE_GAP_ADDR_TYPE_PUBLIC...
Hello,
I made 10 custom board with nRF52 rev C, epson 128FA 128 32 MHZ, epson FC 135 32,768 KHz
I have some difficulties to get crystals working.
10 of the CPU run...
