Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions: ...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I use NRF51822 as a transmitter in "gazelle mode" so no soft-device is enabled. At the other end I use NRF24LE01 as a receiver. In order to see what is going on in...
Hi All.
I made a nRF51822 based PCB with SWD header but I don't have any J-Link lite to load Firmware.
I have a nRF51822 Eval Kit. Is there any way to use the J-Link of...
Hi,
I am using nRF51822 and I compiled and loaded uart example code. Also i used nRF toolbox android application on samsung s5 with android 4.4.2.I am using sofdevice 6...
Hi All,
I would like to broadcast 256 byte data in one shot every second, any reference in SDK recommend?
Thanks in advance.
**updated at 19 Sep, 2014
Application...
Nordic,
After upgrading to S110 7.0.0 the BLE_LBS example no longer works as downloaded from GitHub. I adjusted the flash algorithm size which fixed the first problem and...
Hi Developers,
I'm using an nRF51822 and finally beginning to understand BLE. I want to learn by example so I downloaded NAN-36.
Im at a point where the Application...
Hello,
i'm using the NRF5182 QFAAG0 chip, its one of the samples from the evaluation kit.
I can program it with keil (not using the S110). Using nrfgo studio i can see...
I'm building a BLE peripheral / observer multi-role application using the timeslot API and based on the example code at github.com/.../nRF51-multi-role-conn-observer-advertiser...
Hi,
this is my first time I write on this forum and I hope to find some useful suggestions for my work on Nordic platform. I work since many months on nRF81522 chip and I...
Hello Everybody,
I'm sorry I'm a little confused about the SDK and S110 versions. Can I use S110 v7.1 with SDK v6.1?
I compiled the ble_app_beacon I found in the SDK...
Is there a way to implement a blocking flash write without dealing with system events. Periodically, every 10 seconds or so, I need to dump a large amount of data to flash...
So I have bought some nRF51822 Beacons to develop with. It was suggested when I purchased them that I wouldn't need any further development kits - but whilst I can see the...
Hi,
When using Master control panel both on PC and my galaxy S3, I can detect and connect to the HID keyboard app, but when trying to scan for Bluetooth devices on Galaxy...
Hi,all!
My question is:
Can one smart phone connects two peripherals(both based on nrf51822) at the same time?
If it can, should the peripherals use s120 softdevice...