Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions: ...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm just getting started with the nRF51 Eval Kit, I have the 5.1 SDK installed, using Mac OS X for development. I also have the GCC ARM toolchain installed. Firstly, I had...
Folks,
I have the S110_SoftDevice_Specification v1.1 (great doc, thanks) and the doxygen-generated API docs. But is there an App Note or other document that fills the void...
Description of my system:
Hardware:nRF51822, pca10001
Software: SDK5.20, S120
If i first call the function ble_stack_init(); and then i open the LFCLK first by set...
Hi,
I'm working with the heart rate demo for the nRF51822 Development Kit and I can only connect and discover with the development dongle and master control panel. If I...
Hi,
I use ble_app_uart project (pca10001) and new softdevice7.
I find a DFU project at nrf6310 directory of SDK .
when i program both projects the uart application...
I am aware of L2CAP API exposed by the SoftDevice SDK sd_ble_l2cap_cid_register(...)
How can I find out if this API will create a connection-oriented and dedicated channel...
Hello!
I would like to use the nRF51822 and build a pcb design in Eagle. While i tried to create a new package i couldn't find any specification for the qfn-48 6x6 the...
1.description of my system:
Hardware:nrf51822,pca10001
Software:sdk5.20,run the softdevice s120
2.the problem i meet,in the main() function
the first i called the function...
Hi,
We are using nRF51822 BLE device in our product. As we got to know that this chip cannot be factory programmed.
Can you please suggest us how we can program this...
Does the following flasher also allow to debug the nRF51822 device?
Segger Flasher Portable
If not... which flasher/debugger is suitable to be used during development...
I'm adding the bond manager to an existing nRF51822 s110 soft device project to enable encryption when reading/writing certain characteristics of a BLE service.
As far...
i am making something about dfu!
i read some message from "readme.txt"
such as :
Program initial SoftDevice
Make sure the device is cleared (nrfjprog --eraseall...
I have trying my best to find the url of ''nrf51_sdk_v6_0_0_43681.msi',but there is nothing i got, i need some help.
Do you know somthing about it? thanks!
Edit: One...