Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I use softdevice s110 7.3.0 and SDK version 7.2.
Some times softdevice call app_error_handler with:
error_code 0xDEADBEEF
line num - 990
file_name - src\ll_ctrl.s0.c...
Hi,
I try blinky with softdevice example and reconfigure it to support nRF51822AA. I can program my custom board, I can debug as well, but led is not blinking. I have connected...
Hi,
I want to set the advertising interval to 10.24 sec.
I changed the value of APP_ADV_INTERVAL to 0x4000.
But when i try to discover my device using MCP, it is not...
I'm trying to track down an intermittent bug in programming our Nordic board. So, I'm having to laboriously reconstruct the SWD transactions and understand them.
A transaction...
I use nRF51822 Model in my project that I need to run bluetooth advertising all time. And when I measured current, I found 1mA that is not enough to run for 1 year by just...
Hi,
My project include two MCU with n51822 and STM32. I expect upgrading STM32 application firmware by n51822 DFU function. Do you give your advice to implement it by modifying...
Hi All,
I am struggling getting my N548 module to transmit any ANT+ ...
I have tried the Cycling Power Sample Application (S310)
And the Cadense / Speed (S210) Sample...
Hello,
Is there any delay between when the reset pin is driven low and the actual reset of the chip. Would it be possible to sense the reset pin and perform some quick...
I am designing an nrf52 based device running at 1.8V. To debug the device I was planning to use debug out option of the nrf52 preview DK. However, I just find that, the debug...
I'm trying to follow the code from one of your examples, specifically ble_beacon in SDK 8.0 and eventually I get to a point where I'm not sure what's going on so I figured...
Hello,
I have question. I using examples with nRF51-ble-peripheral-bond-handling with bls_service (PCA10028) and i have problem with unnecessary connection. I want that my...
I'm referring this blog on getting started with nRF51822 and in this same blog, there is a link to a video by Nordic on Introduction to Bluetooth Smart and after watching...
I have two STM8s105 MCUs and two NRF24L01+ modules. Set one as transmitter:
CONFIG: 0x3A
EN_AA: 0x00
EN_RXADDR: 0x03
SETUP_AW: 0x03
SETUP_RETR: 0x00
RF_CH: 0x00...
Hi
I used the boot loader example successfully on the nrf51DK board.
Now I want to use it on my custom board. So I recompiled the boot loader code, with 1 difference:...
