Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi there,
After prototyping a device with modules and on a breadboard, I transitioned to a custom PCB with nRF24L01+, matching network from the spec sheet, and 2.45 GHz...
Hi everyone
now i used softdevice s120 scan and connect two s110 device
and i used sd_ble_gap_rssi_start() when connect event ,
then get the rssi in BLE_GAP_EVT_RSSI_CHANGED...
HI,all!
Recently my nrf51822 device encountered a tough issue,the detials are:
My device connected to an android app, which has some bugs about ble connection so the...
HI,
I am using sdk 8 and pca10028 dk. I follow following procedure,
Program the softdevice using nrfgo
Program the test_bootloader using nrfgo
Program the application...
I have some questions about how I will use this structure ,first of all I know that The "data" member of the ble_gatts_evt_write_t is meant as a placeholder for the address...
I am trying to create a windows app that will read data from an accerometer via a nrF8001 ble module.are there any example i can see for communication between windows and...
Hi, Nordic Engineers. Now, i use a external 32mhz crystal on my board. i have add code"NRF_CLCOK->XTALFREQ = 0X00", but the BLE radio seems not work. Led flick is ok.
Why...
Hi Guys,
I have a SITECOM Bluetooth Dongle connected to my PC and I want to receive data from nRF51 DK via bluetooth (for example heart rate monitor data).
Could someone...
Hi everyone,
I must to comunicate from HW to PC with SPP over BLE. So I took the dongle BLED112 (side PC) and the HW where is mounted a nrf51822 like uart BLE interface....
Hi,
the product specification of the nRF51822 states the possibility to carry quadrature demodulator
signals on GPIO pins.
This would let one allow to observe the physical...
Hi,
I am a newbie to nrf, I am trying to understand the lbs example while running on nrf dev board. I want to set my application as follows:
Blinking LED while advertising...
Hi, I have a problem with the HFCLKSTARTED interrupt.
I can't have it. (I'm a little bit pressed with time I have to send a document in 2 days, so if you can quick respond...
We are currently using SoftDevice 5.2.1 and was given the task to migrate to 6.2.1. I doing so, I placed 6.2.1 hex onto our device and turned it on. Yikes, many errors. Most...
