Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I use the demo : ble_app_proximity
to connect with android app
In android use this :
mBluetoothGatt = device.connectGatt(mContext, true, mGattCallback);
to set the reconnect...
Hi,
I'm checking out the new nrf51_sdk_v6_0_0_43681 for S110-SD-v7
Is there a revision-history available for the src files within the new SDK package?
For example...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Hi all,
I have been stuck trying to debug the example project for a couple of days now and could not find the answer through searching. Here are my problems.
Background...
Hi All
I have a bunch of nrf51x22 (4,8) and I'd like them to read their own firmware data and send this to others that are in DFU mode using the over the air (OTA) method...
Dear Nordic Developer Zone,
I'm using nrf51822 EK testing the GPIO sense function. The code I'm using is based on what a nordic employee has posted elsewhere in this dev...
hello,
i was trying to compile the softdevice s130 example code given with softdevice download from nordic.
I am using the ARM-MDK lite 4.74 version. It is showing error...
My design goal is to conserve as much battery power as possible on a device that typically gathers data 30 to 40 minutes per day. To that end, our thought was to make the...
hi~
6.2.1
Updated Setup_JLinkARM_V490e to Setup_JLink_V492
Updated nrfjprog to version 5.2.0 (see own release notes for changes)
where is release note ??
i can...
Dear all:
I want to constantly transmit messages from a nRF51422 to an other nRF51422 with specific ID by ANT protocol. Then, I want to receive the messages from one to...
Hi,
I want to build a Tx that can reconfigure a channel(like change the device's number) after finding out a long time failed to send message.I use the way below:
sd_ant_channel_close...
hiii...
i hv made a custom profile with concurrent broadcast feature tested in master control panel and some other phone app... working properly.. but wen i tried in iphone...
Hi,
I try to open ANT+ channel and make sure the status is searching or tracking,
but if I use pstorage to update flash in the same time,
It will response timeout...
We are developing a keyboard for smart phone or plant and what to make different surpport for different device.
So can I make difference from ios device and Android device...
Please indicate me if there is a data port on nRF8002 after you burn out OTP, Can I use this I'c for data transmission. Please indicate communication port for this chip. Also...
