Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello Everybody,
I have a question about nRF51422. I want to monitor the ANT+ message from any sensor, which is already connected with the device,
Scenario : if it is...
Hello,
Im trying to create a synchronisation method for sensors using BLE. At the moment i can synchronise them within 10ms accuracy, in theory it should be within 2ms...
Dear all:
same as this issue:
devzone.nordicsemi.com/.../use-dfu-to-update-ap-over-ble-single-bank
it seem same as my way that modify modify "dfu_dual_bank_ble" target...
A big update this week for our S110 SoftDevice. Full OTA DFU for SoftDevice and Application. Also Multi-acivity concurrency for Bluetooth Smart and 2.4GHz protocols. As Developers...
Hello
I got my nRF51422 DK, and got few inquiries
For ANT,BLE DK, where can i find API documentation?
BLE can be implement on nRF51422 DK?
Is there sample project...
I have a 'fresh' nRF51822 on a board and it's not clear to me what procedure I need to follow in order to get it to work. I'm using the Segger programmer and I can program...
In the Keil debug interface, how can I find if the application is throwing an ASSERT, and which it is? I'm using the S110 softdevice. (See other question for context devzone...
Hello, I have a weird problem, the nRF24L01+ is sending a TX PAYLOAD that was left in the TX FIFO (clocked with W_TX_PAYLOAD) as an ACK PAYLOAD when switching to PRX mode...
hello everyone,
i am trying to use SDA and SCL pins of TWI other than 24 and 25, is it possible? i want to know before using other pins for twi other than 24 nd 25 with...
Hi
I try to communicate with others TWi devices using the twi_hw_master driver.
When i initiate a communication with twi_master_transfer , i don't receive any ack from...
Hi,
I have purchased the nRF8001 Development Kit and so far I wired the nRF2740 board to a FTDI VNC2 microcontroller. I have been reading about how to configure the 8001...
Hello. I'm trying to port the ble_hrs to a custom board with an NRF51822 on it, but the advertising never starts. While I'm debugging this, what should I be looking out for...
Is there an example for sleeping? I just want to put this thing to sleep drawing minimum current and have it wake up on a RTC timeout, but do not seem to be able to achieve...
