If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Is there a working example with using gpio_dt_spec for accessing gpios?
I used the code provided from https://docs.zephyrproject.org/latest/reference/peripherals/gpio.html#c...
Hello, by usingnrf52832 DK and testing some examples i found out that the example peripheral UART was not going like I wanted to do. He is going to sleep mode after 3 minutes...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v1.0.1%2Fmd_doc_getting_started_how_to_models.html
Linkte verilen yönergeleri takip ederek...
Hi all, I discovered that if I get BLE_GAP_SEC_STATUS_AUTH_REQ while pairing, the device is basically useless until a new reset. I would be extremely grateful for some help...
Hi All,
I have a project which uses the zephyr shell, but I can reproduce the issue with zephyr/samples/subsys/shell/shell_module or any other sample making use of the UART...
uint32_t address = XIP_ADDRESS + addr ;
uint8_t * p_data = ( uint8_t * ) address ;
for ( int i = 0 ; i < len ; i ++ )
{
data [ i ] = p_data [ i ] ;
} The Pin of QSPI...
Hello,
I recently installed the VSCode Extension for nRF Connect and I am experiencing, what seems to me, strange behaviour.
Here's the steps:
I create a project from...
Hi
I modify the ble_app_uart_c example to support connecting multiple nus peripherals.Calling the new_cccd_configure(p_ble_nus_c, true) return error after nus_c discovers...
Hi,
I am using nRF Connect 3.9.1 and power profiler 3.2.1. I have noticed that if I have a measurement on-going and go away for a while (4mins tested while writing this...
Hi,
I am using an nRF52840 with SDK 17.0.2 and S140 7.2.0. I am running a scheduler based on app_scheduler.
I am trying to make my FDS implementation blocking as it...
hello ;
i am new for nRF52840 DK , i just want to learn how to use it , i need to deploy to bluetooth (ble5) on nrf52840dk to connect or send the data to esp32 , however...
Hi All,
Due to chip shortages we have to replace nRF52832 with nRF52810 in our design. Our application has to perform BLE scanning, but no other functionality of a BLE central...
My nRF is a central and the iOS device is the peripheral. the nRF connects to the iOS then checks via pm_conn_sec_status_get() if pm_conn_sec_status_t is encrypted, if not...
Hi I work with ble on nrf52833 I want to send my collected ble datas with uart1.In my code poll out working but fifo fill doesn't work. Any basic simple for fifo fifo fill...
