Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I'm trying the given example < twi_sensor >. I connect nRF52 DK P0.26 to my sensor's SDA, nRF52 DK P0.27 connects to my sensor's SCL. My sensor runs at 400kHz, so I modified...
Hello, I'm new for mesh, have a question about the mesh dfu bootloader.
the source device of the mesh dfu shuld be connected to a host. how to assign the uart pin? is it...
I have to integrate a softdevice into an existing nrf52833 SES project. All the documentation I have found isstarting from any of the examples and using GNU Linker instead...
Hi,
I am trying to create an application for nrf52810 soc. I have a problem on selecting board name and the SDK version
I am having nrf52DK (nRF52832 soc) development...
Folks. I developed my own circuit using nRF 52833 and I`m trying to upload a new firmware via SWD interface. I'm not getting connected to the target for any reason. Is there...
Using SDK 17.0.2 and the nRF52840DK, I am setting up SPIM with a memory IC (not actually hooked up though, just looking at the signals on the oscilloscope). This code is executed...
I'm facing a problem with a product I'm developing. The problematic setup is as follows:
Two nRF52832 peripherals (S132 v6.0.0), each notifying on two characteristics...
Using: Windows Pro 10.0.19041 Build 19041
I'm trying to run Trace Collector for an issue with the nRF9160 and FOTA. I go to run the Trace Collector and it starts, but says...
I am using nRF52832. For reading ADC value for battery level percentage i have used 800k and 1M ressitor value. But while reading ADC Current cosumption is reached to 3 to...
I am trying to copy from this example:
https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode
but I get:
./nrf5_SDK_Current...
Hi,
I'm trying to understand the PSM availability of my local network.
After playing a bit with the RAT and RPTAU values, I found out that using RAT=16~30 secs and RPTAU...
Documentation states that k_fifo_is_empty() returns 0 if data is available in the fifo (which is really implemented using a queue).
I'm receiving some spurious interrupts...
Hi,
In these conditions "custom device connected+bonded and whitelist enabled", when the device scan for beacons it see only the smartphone bonded to the device (don't see...
