Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi nordic community
I am trying to send stop command to my device(which is connected to my NRF 52840) from my ble module(NRF 52480) after my android disconnected from the...
Hi Nordic engineer:
When I used examples\multi protocol\ble thread\ble_thread_dyn_mtd_coap_cli, I found that the device could not automatically assign LEADER, Router, and...
Hello and Thank you In Advance for Your Assistance. I have been working several days just to get a UART running for interface to a peripheral.
I am trying to connect a UART...
Hi,
As per the document(nrf91_at_commands_v0.9.1) for GPS SNR testing command "AT%XRFTEST=2,1,0" output is single integer as below .
but i am getting output like below...
We are using nRF52832 in our design. We want to collect sensor information along with time stamp. So I took nRF calendar application and tested the same. It was working fine...
I have developed an application that reads data from an analog sensor and transmits data with UART. This app is based off the SDK v14.x uart example, and SAADC example. While...
Hi.
I am developing zigbee product with security function (using install codes).
1. function cmd_zb_install_code in zigbee_cli_cmd_bdb.c, there is a comment as bellows...
Hi, I'm using proxy_client and proxy_server from light_switch examples of mesh sdkv2.1.1. The provision process gets successful with android mobile using nRF Mesh App but...
1. Do I need to make hardware changes when I want to change my SoC chipset with nRF 51 to nRF 52? 2. Does the nRF52 Series require hardware changes when it needs to change...
Hi,
There is a Demonstration about zigbee joining networks by install code.
But how to know if it using the install code instead of the default TC link key?
1. I run...
Hi
I am working on cryptography algorithms. I am trying to write my own implementation of main function. Inside the main function, I wish to call AES functions. I want AES...
Hi,
I am trying to use nRF52832 evaluation board as a BLE sniffer. I have windows 7.
I installed nRFgo studio and downloaded nRF Sniffer v1.0.1.
I plugged the board...
Hi! I'm new developing using real C language. I have more experience using Arduino. I'm trying to send a MIDI message over Bluetooth MIDI when I push one of the buttons of...
Hi,
we've just found the information about the knobattack ( https://knobattack.com/ ).
Is there any fix for this issue with the new updates?
Best regards,
Constan...
