Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I have an application that tries to configure pin 9 of port 0 on the nrf52840. this pin is reserved for NFC use. in one application it was enough to add:
& uicr {
nfct...
Hi ,
In NCS 2.8.0 the ESB-PTX sample how to config to achieve?
Now I had disable the UART log,after transmit 20 seconds I want to config the nRF54L15 into a low power...
There are 2 software: 1.0.1 and 1.0.2. When I load the 1.0.1 hex with bootloader with the programmer, it draws 9uA current. But when I update it to 1.0.2 with DFU, the current...
We are flashing the nRF52832 that works with DFU with a SoftDevice and a bootloader. The application code is compiled privately with a private key and packaged into a zip...
Hello Nordic Team,
We have a customer who needs to use the Nordic Distance Toolbox (NDT) functionality, and they are hoping to demonstrate it on the nRF54L15 DK. Is there...
Hello, I've tried to implement rtt logging in my own project but the control block cannot be found. So I tried the saadc example and that did not work either, I tried to use...
How do I use hardware crypto on a nRF9160dk? I am using the nRF connect SDK and my build is nrf9160dk_nrf9160_ns.
Would that be cryptocell or something else? If it's cryptocell...
I am using nRF52833 / NCS 2.8.0. I'm using Gazell Pairing, but I only need pairing, not encryption. So I'm only using unencrypted pipes. If it is a non-encrypted pipe, it...
Hi,
In my design, I have a push-button that pulls low when pressed and remains floating otherwise. This button is used to wake the nRF52832 from system off mode.
The push...
Hello nordic:
May I ask about the requirement of 32M OSC of 52832 ?
EX:
Frequency tolerance
Equivalent resistance
Loading capacitance
shunt capacitance
Drive...
Hello Nordic team,
I am working on MCU nRF5340 and NCS v2.6.0 for BLE secure pairing level 4 with adding LTK (Long Term Key) share support. But, I am unable to find the...
Hi, I am currently designing the schematic for nRF24L01+ module interface with arduino nano atmega 328p MCU. Due to inventory restrictions and the current soldering capacity...
I have the SH6MDBT50Q BLE module, and I need the nRF SDK to implement a Bluetooth Mesh connection for transmitting and receiving data on both sides. I am using Segger Embedded...
