Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
As Pevious ticket: Using NRF24L01+ with pure assembler programing becomes very long, I open a new one as Torbjørn suggested
This is a description about what I have doing...
Hey,
So I was trying to flash the audio application on my nRF5340 audio dk. I built the program successfully using the buildprog tool provided.
The problem here is, I...
Hello I want to make an application that will be sending data from 3 peripheral BLE devices to the central device which wil be connected to PC and transmitting data (from...
Hi,
as soon as I include CONFIG_REQUIRES_FULL_LIBCPP=y in my prj.conf I get an error "undefined reference to `_impure_ptr'" when building:
This happens when I try...
When I developing application with nrf SDK,I can set device name by sd_ble_gap_device_name_set().
But when I turn to NCS,I should set device name such as CONFIG_BT_DEVICE_NAME...
Hello everyone I am using Nrf5340 Zephyr sdk v2.4.2 to broadcast BLE as a peripheral connecting 2 devices with Esp32 as central and phone at the same time, the following error...
Hello,
Does anybody know why I can not discover the service uuid as shown in the picture below?
I want to connect a sensor with this chip nRF52832, it's service UUID is...
Hello,
I'm using nrf52840 USB Audio headset application on nRF52840 DK. The nRF connect SDK version is v2.6.0.
I want to change the output to i2s out. The following are...
Hello, I have a few questions about sending code via J-Link. We are doing our project on vscode with 2.6 sdk. When working with nrf5340dk, flash via vscode was enough. However...
Dear lovely people from Nordic Seminconductor,
I have the nRF52840 dongle.
I installed the software ""nRF Connect for Desktop" on my Ubuntu 24.04
For that I ensured...
Hello,
I am using the NRF52840 dongle, and for my project I need to be able to send/receive data from a RaspberryPi and also send/receive large strings between multiple...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I want to use Emulated RTC driver functionality.
Therefore, I configured prj.conf file as (based on This Link ): CONFIG_RTC...
Good afternoon,
For a beamforming application in the Wi-Fi range, I am planning on using an nRF24L01 to generate the signal.
The signal would later be split into N different...
Hello,
So I have an IO Shield with the nRF5340 SoC. I have connected the IO Shield to the Port 12 of the nRF5340 Audio DK as shown in the schematic:
Connections:
Debugging...
