I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I have my software set up so that it does some computation within the Attribute write callback function like this.
b roadcastKeyHandler does somewhat of...
We designed a board based on the nRF52840, and are using nrf5 SDK 17.1.0 with S140 SoftDevice. The board has an RTC, LSM6DSO as IMU, an opamp front end for the analog inputs...
I am looking at the "mesh_shell" example project. I was able to build the sample for nrf5340 dk this way:
- create a new build configuration for "nrf5340dk_nrf5340_cpuapp...
I am working with an IQS572 capacitive touch IC, and when communicating with this IC, the communication window will shut down if it receives a STOP bit.
I am writing a lot...
Dear all,
I am use nrf5340_audio_dk to run the audio_application and I use the BIS mode. I post 2 loggings at the headset device as the broadcast_sink. All things seems...
When I try to build the SDK example WiFi monitoring it showing error, C:/ncs/v2.6.1/nrf/ext/oberon/psa/core/library/check_crypto_config.h:80:2: error: #error "PSA_WANT_ALG_DETERMINISTIC_ECDSA...
As far as I can tell, it is not currently possible to implement the following functionality in a simple way with pynrfjprog across the various device families.
* What is...
Dear Sir/Madam,
I am using Zigbee: Light bulb — nRF Connect SDK 2.6.99 documentation (nordicsemi.com) this sample to do an evaluation, and I would like to change the tx...
I'm trying to do an ADC measurement on AIN6 on an nRF52832. This is how I have things set up:
proj.conf:
Overlay file:
ADC initialisation (this gets called on power...
Hi Support Team
We are testing the sensing of zephyr sample in the below directory with nRF52840, but we can't find which callback function is used to get the sensor data...
Hello,
Im trying to update the custom nrf5340 board over BLE. I have managed it using nRF Connect and Device Manager.
I can upload it using nRF Connect, but I need to...
Hello!
We are on the process of implementing our own desktop program to run DFU over BLE, similar to how the nRF Connect application does it. We are using SDK 17.1.0 in...
Hi ,
I would like to know if we can use 2 PPK's in such way to measure both direction.
As you can see in the diagram , the current can flow to the battery or can flow...
The bluetooth program refers to app_ble_uart. Bluetooth uses nRF52840. I use stm32 MCU to transmit data through UART. The baud rate is 460800 for transmission. The UART transmission...
