I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I am working on a module MS12SF1(nrf7002 + nrf5340) module. I am getting uart data from another device to this device through uart. Earlier when I configured uart to its by...
We have some custom hardware that acts as a peripheral, and currently has the advertising data packet set up as follows:
BT_UUID_SPD_SERVICE is our custom 128-bit UUID...
Hi.
We moved to version 2.5.2. Here we encounter some problem with data mode. Sometimes we don't get response of exit from data mode.
We publish data, after we send "...
Hello Everyone,
I wanted to ask if there is a way to use SonarCloud for analyzing a firmware based on the nordic toolchain v2.5.2, I understood that I have to set up the...
The MDS service supports the chunks through Bluetooth GW. in reality this is not of much use in real scenario. So is it possible to upload the chunks directly to memfault...
I am running the demo of "nrf-knx-iot/samples/light_switch_actuator" on my customized board based on NRF52840.
I could burn the light_switch_actuator firmware into this...
I posted my configuration in a separate discussion .
Calling this method works when CONFIG_BOOTLOADER_MCUBOOT=n works. But as soon as we flash an image with MCUBoot enabled...
Hi Support Team
We add below code to the while loop in the main.c file of NCS sample https_client to post data to server. But it can not recover to post data to server...
I'm trying to import the native libraries to Xamarin forms, I need for the FirmwareUpgrade section of the iOSMcuManagerLibrary. I compile the example project correctly and...
Hi,
I'm using the NRF52805 with the QDEC.
As far as i saw in the datasheet, the QDEC suppose to take about 5uA But when i operate it is takes about 500-700uA !!
...
Hello,
We need to use some fixes that aren't released yet in a version yet. Specifically, an MCUBoot fix: github.com/.../303
Is there a guide as to how to use forked version...
If I purchase a Zigbee endpoint device off the shelf (for example an SOS button) and I added to my nrf Zigbee network(routers and coordinator and other endpoints I have developed...
Hi,
I am trying to use BLE time sync code and it seems working well with 16Mhz timer and rtc as well.
Here is the previous ticket.
One thing I noticed is about...
As shown in the above picture, 1. Choose 10000 beat times for monitoring. Why is there a significant difference between the pulse peak and the peak of selecting 100000 beats...
Hi,
Im currently adjusting this i2s sample code to work with my TAS2781 audio amplifier. The code works perfectly but I just want to do a little adjustment on the channel...
