Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello, I'm working with BLE Mesh using NRF52840
- Our setup: NRF-Connect-SDK 2.1.0
- Summary of our project.
+ Provisioner node to control lightness for all nodes in...
Hi,
I'm having an issue including USB DFU Trigger library in my prototype application running on nRF52833.
My application is based on the ble_uart example, to which I...
Hi,
My application is written on top of freertos ble example. I need to integrate radio test example as well for certification. I am running into errors when I try to...
Hello,
my first Post here, so i hope i do it correctly.
I have the following Problem with the Configuration and Communication over TWI/I2C.
The Voltage of the TWI...
I am working on BLE on NRF52840 using soft devices for BLE and I was using sd_ble_gap_ppcp_set API to set the connections parameters for the BLE so I think the PPCP is the...
I'm calling this function from a Zepyhr project:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/connectivity/bluetooth/api/gap.html#group__bt__gap_1gad2e3caef88d52d720e8e4d21df767b02...
Hi, I am trying to test multi_sensor example from Zigbee and Thread SDK 4.2 using official Nordic nrf52840DK with few Zigbee hubs. Example is located in \examples\zigbee\experimental...
Hi
My thingy91 does not appear in the Connected Devices list in VS Code. I've tried everything now.
What's the prerequisites for getting this to work?
Do I have to install...
I'm using a nRF5340DK with nRF Connect SDK v1.9.0 and want to use MCUBoot with Direct-XIP.
Using the hello_world sample project, I added MCUBoot.
In the MCUBoot prf.conf...
I have issues with my NRF5340DK devices that I'm hoping to get support on. Several devices appear to be bricked, stuck in a boot loop or otherwise unable to program using...
Hi, I'm hoping someone could advise on interfacing with the T2 LC3 codec included in nRF Connect.
The context is I have stereo I2S microphones providing 24-bit 2's complement...
Hello, As part of a student project I am looking to learn about Nordic technologies for BLE and ANT. The goal of our end of study project is to provide an extremely accurate...
If I would like to add Bluetooth capability to the nrf9160, can the nrf5340 be used as a "companion" MCU?
Would be great if there is a pre-build firmware for the nrf5340...
