Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi, we are currently trying to reduce the power consumption on our product that uses an nrf52810.
An 1k pull-down resistor has been used on the SWDIO pin, but I don't really...
Hi,
I am using nRF52833 & nCS for an application development,
I am facing a curious issue where, if i enable printk in nCS build, I am getting SUCCESS on calling device_get_binding...
I'm trying to join two programs that work well by themselves, a saadc program that shows the force sensor value in the serial, and a BLE program that turn on or off a LED...
Hello every body,
I'm now utilizing the nRF9160 to develop several products based on SDK 2.0.0. In my program, I must produce SBOM.
This link below has some information...
I am on project using nRF52832 WLCSP.
What's the pin assignment for SWDIO pin? I want to read the input of SWDIO (as indicated in datasheet it's Digital I/O) and can it...
Dear Concern,
We were developing one of our products using nrf52840. We previously used the nrf-52840 USB dongle for the product. Now we were moving to nrf52840 chip based...
Hi,
nRF5340 + nRF21540, NCS2.0.2, VScode
i follow Working with RF front-end modules — nRF Connect SDK 2.0.99 documentation (nordicsemi.com)
how to disable TX_EN? i only...
Hi,
I am using SDK 16.0.0 and nRF52833. In which TWI (master mode) is not working.
Pressure sensor is connected over I2C. (NRF_DRV_TWI_INSTANCE(0))
Previously I am...
Hi to all!
I'm trying to use the same GPIO to wake up the nrf52810 from system off and also use it to execute some functions. I have this code that is based on the example...
I'm trying to load a program to a custom pcb with a n52832 chip, but shows up this error in the Programmer: Failed to load readback protection status: async task failure for...
Hello,
I am working on a project that modified from ble_app_uart_c, with sdk v16.0, softdevice S140
In my case, I defined an event observer by
NRF_SDH_BLE_OBSERVER(m_ble_observer...
Dear Mate,
I am using bl653_dvk board i followed this link clearly (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi...
