I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello there,
I am getting "No devices connected" error message when trying to erase and flash to Arduino Nano 33 BLE sense board using the nRF Connect for VS Code. I also...
Hi Guys,
I am working on the nrf52840 and using SDK 17.1.0 version.
i am creating the zip file of my application code using "nrfutil pkg generate"
It give .json, ...
Hi,
On the nRF5340-DK, i'm succesfuly using the example code:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_uart/README...
Hello Support,
I just started to play with the self provisioning "Mesh-Demo" sample to get a hang of the BLE Mesh. Since I am working on the nRF52480 DK and don't have a...
Is the Common Application Framework considered ready for production use? The fact the "Common Application Framework overview" page links to "Common Application Framework preview...
This is a follow-up to a previous ticket https://devzone.nordicsemi.com/f/nordic-q-a/83842/error-when-building-configuration-for-non-secure-boards , the problem persists and...
I have connected a nRF5340 DK board which the Programmer can connect to. I then drag the two .hex files for the Heart Rate Monitor demo over to the File Memory Layout window...
I've was able to use brand new PPK2 to make test measurements few days ago and it was working fine. I've connected the unit today and software have issue recognising the device...
After reading through the nRF21540 datasheet, I have a few questions.
1. Is section 5.5 saying that even though the spec for VDD is 1.7-3.6V, VDD needs to be between 3.45...
Hello everyone,
I'm now having a problem while using nrfx_spim_xfer on nrf52840. I want to use nrfx_spim_xfer with a callback when transmitting is done.
My setup code...
Hi,
For a development evaluation, I am looking to program nRF52833 to have it interface with "IS25LQ040B" serial flash chip through SPI-1. I found lack of examples and...
I am using the "nRF5_SDK_17.0.2_d674dde" for nRF52 development.
Would like to get the SoftDevice and nRF52 device for confirmation after OTA.
1. When using the sd_ble_version_get...
I am trying to send a OnOff output cluster information to Co-ordinator when a button is pressed in the nrf52840 DK. The problem is the during the initial registration, the...
Hi.
i want to power my nrf52840 with 2 AAA batteries i connected them directly to the module. Is there any Bluetooth signal strength difference when battery voltage drop...
Hello !
I have taken example /examples/crypto/nrf_crypto/aes/aes_ccm
and modify & g_nrf_crypto_aes_ccm_star_128_info instead of ccm
and initialization is failed
...
