Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I'm trying out nRF Connect running inside VS Code and I'm running into issues debuggin my code. I followed the Nordic setup tutorial and installed the latest nRF...
On a freshly installed Windows 10 system, I've run in to a problem with the JLinkARM.dll and nRF Connect for Visual Studio Code. If I download and install the latest JLink_Windows_V756b_x86_64...
When I clicked the debug action for my app, the following error window popped up.
I followed the below steps to create the app:
1. check my default directory of...
Hello all,
I am trying to do a simple task, yet I cannot manage to make it work. My goal is to use the GPIO 1.01 (defined as Digital I/O in the Data Sheet) as an output...
Hello All,
This is from an app I had working 1 1/2 months ago - when I've tried recently to get it connected again, I haven't been successful.
The latest asset tracker...
hi!
when resetting the coordinator (zb_bdb_reset_via_local_action(0)), an error occurs, the program hangs. It looks like the "zb_address_unlock" function. The same when...
In the description of example BLE Heart Rate Collector, it says that it can indicate state BSP_INDICATE_SCANNING and state BSP_INDICATE_CONNECTED.
In the description of...
I have updated the Programmer to v2.0, and connect 52840 with JLINK to my computer, but it can't be selected in Programmer. Previous version runs normally. What can I do?...
Hello! I'm trying to use an external module with the VSC extension and I don't think that is currently supported (or easily supported.) For reference, our module works with...
Hello, I'm trying to manage connecting to my board (nRF52840-DK) which direct advertise (low prio) with peer address set to MAC address of my PC running Linux with bluez 5...
Now I have a problem, the transmitting power of NRF52810-QCAA is too low, only -2.73dBm. I tried to adjust the value of the capacitor, but the effect was not obvious. Excuse...
Hi, I tested the RGB Led (with an external RGB Led) with the nrf 5340. But I didn't find any pinout with a brief overview of all the pins and their features because the PWM...
I'm trying to setup the SAADC, I do this as much as possible without examples, so I really understand what is going on.
Setting up:
After this I try to start an ADC...
Hello DevZone,
I am trying to build a NFC driver but I am getting issues with it reinitializing every time I detect a field.
I am unable to use the T2T and T4T libraries...
