Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
We want to use GPIO_12 as a wake up pin. (High -> open uart, Low -> close uart) Also, we have a timer and timeout set to 500ms. When we pull GPIO_12 to high, it seems not...
I'm working on NCS 1.6.1 for both nRF52840 and nRF9160.
I'm trying to put my devices into sleep mode so i reviewed some related tickets and found following ways.
NRF_REGULATORS...
Hello,
I am quite new to NCS. I am trying to sending UART data from nRF52dk_52832 to PC.
The example is nrf\samples\peripheral\lpuart.
If I enable the example with CONFIG_LOG...
Want to realize a function: stop broadcasting after a broadcast, update the broadcast content, and then start broadcasting again after the specified timeout. How can I judge...
I am using the nRF5_SDK_17.0.2_d674dde and the nrf5_SDK_for_Mesh_v5.0.0. I am using the nRF52 development kit and I want to know if I can use the flash fstorage on the mesh...
Hi. I am working on a project and am planning to offload most peripherals to the net core; a few are listed below. Is this a bad idea? I realize I might run out of flash memory...
hello ,
During my twim0 initialization, I have configured clear_bus_init as true and hold_bus_uninit as false. But i always get hold_bus_uninit as true.
then I dig into...
Hi!
We would like to install approx. 2000 pcs BLE devices in a mesh network. The device density is quite high (2x5 meters matrix, same level, no objects).
I think only...
I am looking for a automation where in the scripts should be able to send the CCCD(Client Characteristic Configuration Descriptor) response within one second.
1.Which tool...
Hi,
On a nrf52840 running SDK 17.0.2 and Softdevice 7.2, while being connected to two devices in central and peripheral role, I observe that on the connection where the...
I'm trying to see if there is a simple way to scan for ANT packets on all supported frequencies (not ANT+, which I know is on a single channel, 2457MHz). Just for the presence...
Hello, I am currently using the logger backend to send information via UART from the nRF52811 to a PC. This works well, but only for one way communication. I would like to...
I have nRF52840 dongles that have something already programmed on it. They are encased in plastic and I have no access to the little reset button. How can I install my SoftDevice...
Hi, I'm having trouble implementing DFU buttonless.
I ran the tutorial step by step in the following link: https://www.u-blox.com/sites/default/files/Add-NordicSemiconductorDFU...
Hi Nordic,
From some cases in the devzone, I know for nRF52 series, the ESB doesn't support 250Kbps mode.
One of my customer employ nRF51822 in their product, so I want...
