I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I am running 1\nRF5_SDK_17.1.0_ddde560\examples\dfu\secure_bootloader\pca10040_s132_ble\ses example of SDK 17.1.0. without changes in the code. The bootloader seems...
I was looking to use the NUS Central project and port it to the PCA10059 (nrf52840 Dongle)
I was going to add the USBD_CDC_ACM so I can port the NUS traffic to a Putty terminal...
Hi,
i have nRF52840 DK.
I am working on radio test code based radio_test example code with nRF5_SDK_17.0.2_d674dde version.
If the transmitter is configured as : (BLEN...
I can't build examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay. I get the following error message:
cc1: fatal error: cannot open 'C:/.../examples...
Hello,
After looking at aws_iot sample files, I've stumbled upon the question regarding how one can dynamically change IDs and certificates for multiple 9160 devices? I...
From yesterdays question https://devzone.nordicsemi.com/f/nordic-q-a/80411/state-of-cs-ss-pin-after-nrfx_spim_xfer I have done a logic measurement and I can confirm that after...
Hi,
schematic for CFAA WLCSP mentioned, QDAA is given in the documentation. I want a reference for Circuit configuration no. 1 schematic for CFAA WLCSP mentioned in the...
Hi
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are trying...
Hello!
I am using nRF52-DK to deploy my programs. I try to use writing to SD card in ble_app_uart_central example. Both fatfs and ble_app_uart (central) examples work...
What are the memory settings in the SES compiler to compile secure_bootloader_ble_s140_pca10056
When I try to merge:
mergehex --merge s140_nrf52_7.2.0_softdevice.hex target_application...
I want to write some values to flash before the watchdog resets. For this I have the watchdog event handler specified:
In the wft_event_handler function I write a struct...
When trying to generate a new project Segger Project for my Project
in the option "Extra CMake Build Options" want to pass something like -DCONF_FILE='prj_test.conf' -DDTC_OVERLAY_FILE...
Hi Nordic team,
Looks like the most recent nrfjprog now supports flashing modem firmware.
I tried it and got some errors. Could you please point me in the right direction...
Dear Nordic Team Support
We face an issue where on different computers, using the same setup, different throughput can be achieved.
Setup:
- Custom Device using the...
