I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I am using QSPI NOR flash (MX25R6435F / MX25L51245G) with nRF5340 . I am trying to enable 4-byte address mode using the SFDP BFP table in the device tree overlay.
When I...
Hello all,
I'm currently developing an application using the ESB protocol on a nrf52840.
I'm trying to calculate the expected current consumption in the different stages...
Hi,
I am working on a project with channel sounding requirements and I have collected some test data. I am using the example codes Bluetooth: Channel Sounding Initiator...
I am developing an application using nRF52833 + nRF5 SDK + S140, and I encountered a strange issue. When I perform an OTA update from a firmware that does not initialize the...
Hi there,
I am using MDBT dev kit based on MDBT53-1M module. I have a simple application of reading an SD card and printing the data on the LOG. While the current application...
Hello!
I bought dev board with this module and plan to use it in my product.
I bought a development board with this module and plan to use it in my product.
While I...
Hi
for DFU is bluetooth used by default. Your DFU app suports only using bluetooth to do a DFU.
Do you have any tools to do a DFU over NFC? Or do I have to write a tool...
## Summary
When running the OpenThread CLI sample on `nrf54lm20dk/nrf54lm20a/cpuapp` using nRF Connect SDK v3.2.4, the application crashes immediately on boot with a ...
Reporting this here as the project GitHub asked that bugs be reported via DevZone.
The latest Power Profiler v4.2.0 has introduced an annoying issue - when running the Power...
I have an application that gets a fix using A-GNSS. I couldnt understand from the documentation how to enable other satellite systems other then GPS to be enalbled in my application...
Hello,
I am trying to run this Android-nRF-Blinky sample from Git ( https://github.com/NordicSemiconductor/Android-nRF-Blinky ) and build failed.
Below is the error message...
I make a BLE/USB MIDI controller that has an NRF52840 receiving sensor data by SPI from an Atmega 32u4 at 2Mhz. The NRF52840 is the SPI master (SPIM3). When I'm using BLE...
Hi there, I am using nrf connect sdk v2.6.0. I have noticed that after DFU update, I am seeing ble bonding lost randomly on firmware side. I did uncheck Erase Application...
We are running some sample code on the nrf54l15 mcu, specifically: /modules/lib/memfault-firmware-sdk/examples/nrf-connect-sdk/nrf5/memfault_demo_app
We can connect and...
