If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I want the received the datapacket from bluetooth to be stored in eeprom and access it when need be .If you have any small exmple codes for the same kindly inform me...
Hi,
We are migrating code from NRF Connect sdk 1.3.1 on nRF52840 to NRF Connect 1.6.1 on Nrf5340. Using SoftDevice as BLE controller on both.
Our existing code uses a...
Hi,
I want to run my application on the latest open thread libraries.
As per the page "infocenter.nordicsemi.com/.../thread_ot_libraries_building.html"
we need to run...
Hi,
We are using the nRF52840 Dev Kit with SDK17 and SD140 without FreeRTOS. There has been discussion in other postings <link> about increased current consumption caused...
Hi,
I am having a NRF9160DK board , which i want to use it for an simplest BLE application which sends the data from NRF52840 to my mobile using a simple BLE application...
Dear sir/madame
In our project we want to implement MAX17260 battery fuel gauge to monitor the battery status in the handheld device.
The interface towards MAX17260 is...
I'm trying to run the HID composite example on a nRF52840 dongle, and its not working:
- I refer to : nRF5_SDK_17.0.2_d674dde\examples\peripheral\usbd_hid_composite\pca10056...
Looks like 2 mistake in the latest nRF9160 production specification:
1: 1Mbps but 1200 in description section.
2: Power consumption could be in uA instead of mA.
Hello,
Sorry for the basic question, but I am trying to customize an application basing on the ble_app_cgms example.
In the debugger terminal on SES I am receiving the...
Hello,
I am currently working on an IIoT product using Zephyr and NRF SDK v1.5.1-2-g76c027893 on the NRF9160 and a WFM200 wifi chip. For this project we are using Civetweb...
Hi
I'm locking for an example like zephyr\samples\boards\nrf\system_off for nRF9160 DK
zephyr\samples\boards\nrf\system_off uses nRF51 DK or nRF52 DK board for the demo...
Dear support team,
I would like to use GPIO 09/10 as a GPIO interrupt.
I just searched and I see that need to define CONFIG_NFCT_PINS_AS_GPIOS.
But I can't do it. Please...
Hello, I'm making a system with NUS of nRF52832 and nRF52840 to sample data with SAADC. I started the system with "ble_app_uart__saadc_timer_driven__scan_mode_03" from Github...
Hello!
There is a sample simple_mqtt which is written for nrf9160 DK. Is it possible to make app_signed.hex file to load in thingy 91.
I tried to change prj.conf and have...
Hi,
Using the HRS peripheral example provided in SDK17 with S140 7.2.0, I am in the process of migrating to a custom board using nRF52833. I have already made some changes...
