I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi.
I'm newer on Zephyr.
I want to use the LOG Output.
LOG_DBG("main.c"); LOG_INF("main.c"); LOG_WRN("main.c"); LOG_ERR("main.c");
Everything works but the color of...
Hi everyone,
I'm developing a new application/product. It will feature a nRF52805 without the LFXTAL but with DC/DC support. I'm developing with the NRF5 17.0.2 SDK.
I...
Hello,
I am trying to commission a device running the CLI sample to an OTBR I configured following https://openthread.io/guides/border-router (the OpenThread official guide...
Hi
in Zephir nrf9160dk_nrf9160_common.dts the SPI pins are defined
&spi3 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin = <19>; mosi-pin = <18>; miso-pin ...
hello,
i am using nrf52832 with sensor which uses uart communication and using sdk 15.2 but i could not get my excepted values in rx buffer which is of 3 bytes and values...
hi,
i am working with nrf52832. system on sleep mode is working ok in ble_app_uart example by commenting " //err_code = sd_power_system_off(); //APP_ERROR_CHECK(err_code...
I'm guessing this isn't the best place to ask this question. Please redirect if you can suggest a better place to ask. Thanks! I'll recopy the question here:
NRF has an...
Using
SW : NRF_SDK_16, SDK_MESH_v4.0
HW: NRF52840 DONGLE.
I have implemented light_switch_client which also has USB part initialization and then added in USB_DONGLE...
I am working on the nRF5340DK and NCS v1.5.0
Acording to this example https://github.com/NordicMatt/multi-NUS , I used the Throughput sample as the fundermental project...
I'm measuring the power consumption of the BLE Beacon example and got the graph below for one beacon transmission. I'm wondering what those smaller peaks are with 1ms period...
Howdy,
I'm evaluating the nRF Sniffer + nRF52840 dongle as a stop gap BLE sniffer solution, but I'm having a lot of issues setting it up.
Re: Installing nRF Sniffer (...
Good morning,
I am working with the AOA module of the nRF Connect SDK. I have been able to configure and program the transmitter with the CTE as well as the receiver and...
Dear Nordic,
we are developing an application based on SDK 17.0.2, it user FreeRTOS and BLE with Peer Manager.
We need to store few data in FLASH without confict with...
