I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello
I want to flash my simple coap server code in nRF52840-Dongle using USB DFU mode with nRFConnect but I did not find COMPORT/ Any Jlink Device after put donge in USB...
I'm using the nRF 52840 Dongle, flashed with nRF Sniffer 3.1.0. I have installed Wireshark version 3.0.7, and configured extcap and profile according to documentation. I am...
Hello Nordic Community,
I am using nRF52840 SDK 17.0.2.
I took examples \ble_peripheral\ble_app_beacon as reference and created mBeacon profile.
Then I created three...
Hi,
We need to store about 4Gb of data. Can someone give some external memory ICs that can be integrated into our application. Looking for a low power small footprint...
Hi,
I am new to Mesh network. I want to implement a simple mesh network which include two devices. One device need to send sensor values(ex: temperature) and another device...
Good afternoon,
I'm facing an issue porting the mqtt simple project of the nrf stack to an application that I'm developing myself.
The issue is, when I try merge prj.cnf...
I use Zephyr RTOS and segger Embedded studio to develep nrf5340 project. in a c file , i configurate spim2_ns below:
#define SPIM2_CS NRF_GPIO_PIN_MAP(0,15) #define SPIM2...
Have there been any attempts to port Alexa AIAClientSDK to nRF9160?
AIAClientSDK lists "AWS IoT Device SDK for Embedded C" as one of the dependencies.
AWS IoT Device...
Hi i m evaluating the nrf5340 and i get this message when i try to download the code to NET cpu and it's a bit impossible to attach the debugger
CTRL-AP indicates that the...
Hi,
My nRF52840 DK has suddenly stopped working. I have tried different USB cables but it's not turning ON when I connect the cable to the J 2 USB connector.
Observation...
Hello
In our application we're using the download client. Here are the cipher suites the modem supports in hardware: https://www.nordicsemi.com/Products/Low-power-cellular...
nRF52840, SD140, SDK 17.0.2
We're using UARTE to communicate with a peer MCU. We're using hardware flow control (CTS and RTS are enabled) and the baudrate is 115200. The...
Hello,
I'm using two nRF5340 MCUs with BLE5.2 audio in an application. I had a couple questions I hoped the Devzone could help answer.
1. On one of the MCUs, I was originally...
sorry for the perhaps stupid question - but despite several hours of intensive searching, I am not getting any further with the start -up of my new and beautiful Thingy91...
I do not understand how to compose these settings.
Using ncs v1.5.0 GPS sample with SUPL enabled.
This works OK on nrf9160-DK using the supplied settings
#define AT_MAGPIO...
