Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello DevZone,
I am using Laird BL651 which incorporates nrf52810.
I am currently at the development stage of my project and I'm experimenting with lowering the power...
Hi!
We are using the nRF9160 in a product. The product brief specifies a max throughput of 300/375 kbps (UL/DL) for LTE Cat-M1 and 30/60 kbps (UL/DL) for NB-IoT. Can you...
Hi,
I have a question about the whitepaper nwp-017.pdf. It is described under the chapter "Equipment needed to tune an antenna" that you have to attach a coax cable where...
Hi!
I am running Zephyr direction finding sample for AoA transmitter (nRF Connect SDK). At the end of main function I read DFECTRL1 register just to make sure that it is...
Hello
I have developed an application on my nRF52840 which allows a smartphone to be able to connect in secure BLE.
Everything works fine but I notice that every time...
Hello,
I have an application where I want to send a packet with a directed PDU form a peripheral to a specific central. As an example if I have an alarm the peripheral wants...
I am looking for a System on Module (SoM) with BLE , LTE and GSM integrated on it with all radio/antenna stuff certified., e.g. a module with nRF91 and nRF52 like Thingy:91...
I am using a nRF52840 dongle having usbd_cdc_acm example code.
Whatever data I am sending it appears only on Tera term. But not in terminal software and arduino serial terminal...
Hello,
I am trying to measure the RSSI value of the Zigbee communikation on nRF5340DK.
Right now I have programmed light_buld into one of the DK and light_switch into...
I have followed https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial
i WANT TO ADVERTISE the battery...
Hi,
Segger SystemView 3.30 (downloaded from https://www.segger.com/downloads/systemview/ ) does not work with NCS 1.5.1. Upstream Zephyr has updated https://github.com/zephyrproject...
Hi Nordic,
I just had Thingy:91 few days ago. I ran this KIT with thingy91_nbiot_2021-03-04_8e8c6089.hex and asset_tracker example in ncs/nrf/applications . I found that...
I would like to send and receive data to/from nrf52832 pins over BLE using android phone. I would like to capture and display output of Force Sensing resistor and control...
To the kind attention of Nordic support team,
We have got an nRF52833 gzll host that has to interact with multiple gzll devices. We empirically saw that (in our case and...
Hello
I'm using the CLI example as ZC and a custom endnode based on the freeRTOS multisensor example (from nRF5 SDK for Thread and Zigbee v4.1.0). Im trying to send a counter...
