I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I'm considering rolling back to the sdk ver 14 to avoid the nrfx vs legacy api confusion.
I plan to use only the 52810 and 52832 SoCs.
Is there any disadvantage to using...
Hi @Vidar Berg
Hope you are doing well ! i need your help regarding the beacon coded phy . I read your post
https://devzone.nordicsemi.com/f/nordic-q-a/69595/problem-with...
Hello.
Trying to compile the AES CBC MAC example out of the box, we get the ferror below.
Your help would be appreciated.
Many thanks,
Andrew
Building ‘nrf_crypto_aes_cbc_mac_pca10040...
Hello,
Updating developer machines to OSX Big Sur resulted in nrfutil failing to execute. The install via pip works correctly, but when attempting to run the binary, the...
Hi All,
We have tested the DFU(nrf52840) from a central to the target device over the BLE. In which a central device attached to the PC(x86-64bit Linux) via a Serial USB...
Hi Folks,
I am facing an issue while trying to perform a system On suspend procedure with a wake up on HITOLOW event.
No event is triggered when button pressed.
However...
I wish to develop a bare metal application (without Zephyr) on the nRF5340.
For this purpose I am unable to find the documentation how to perform Inter Processor Communication...
Hello
I used sdk v17.0 and nRF52DK.
I wrote a code that can turn on/off various functions using buttons and apps. And I don't think there's a problem up to here.
And...
We are in the process to add spectral sensor to zephyr based BLE sample, but following the tutorial to add overlay or copying other sensor configurations not helped much....
It has been said that Nordic SDK v4.1.0 for Thread is in maintenance mode. I was told that I should move new Thread development to nRF Connect SDK. I am trying to explore...
Are there any examples of libuarte enabling both uarts in the nRF52840 at the same time? I have been trying now for a full day and keep having problems with what options to...
Hi,
I have an app based on freertos_hrs example (nRF52832, SDK14.2)
I'm trying to get it into low power(sleep) mode, however the idle task keep on running and the system...
Hey all. I was testing DFU over USB on an nRF52840, SDK 17.0.2 and I can't seem to get the actual application to run after a successful DFU. I generate my own keys, use them...
Hello,
SDK51 appears to be an inconsistency with how various BLE related events are handled in the SDK. Multiple BLE event handlers may be registered using the NRF_SDH_BLE_OBSERVER...
I'm currently implementing a DFU "controller" in C on the nRF9160 for performing serial DFU with the nRF52840 and believe I have discovered a bug.
My firmware image was...
