Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
SDK: 17.0.0
Softdevice : S140
Example: ble_app_blink
I modify this example to long range adverting mode,and have some questions as follow:
(1) the device can not connect...
Hi there,
I'm working on a Zigbee project and I'm using the nRF5 SDK for Thread and Zigbee v4.1.0. For benchmarking purposes I need to read the number of hops a Zigbee-packet...
Hello,
I am doing on a project which send data from sensors node to thingspeak, and I am now struggling about implement mqtt to publish data to thingspeak.
best regards...
now i use segger development tool ,but can not breakpoint. but log aseggerlso cannot output information.
V4.2.
my colleague's will do
thanks
best regards!
II'm having issues communicating to the MLX90614, datasheet attached. It seems that I have everything set correctly and the TWI Scanner returns addresses and data. My output...
I am looking for a zephyr based sample code to use an external QSPI flash (MACRONIX MX25R6435FZAIL0). The code is run an nRF52840 based custom board
Your help is appreciated...
Hi,
the nrfx driver for the internal temperature sensor has been introduced with SDK 16,0.0, Since I started developing with SDK 15.02, I have used so far the old HAL driver...
我对NRF6707 Power Profiler套件第一次使用有一些疑问，我想问你 ：
用Amr仿真器JILNK连接NF6707 报错 log日志如下:
2019-11-22T05:21:57.594Z INFO Application data folder: C:\Users\dell\AppData\Roaming\nrfconnect...
Hi
I'm testing heart_rate_collector in pc-ble-driver. in CONSOLE application, it work well.
but in Win32 Application, it doesn't work when run sd_rpc_open().
error code...
Hi Nordic
I want to integrate a push button with 52833 p1.8, base on mesh-sdk light-switch example, (i.e., I may need to modify simple_hal.c)
But after my hours implementation...
Hi,
in some earlier discussions https://devzone.nordicsemi.com/f/nordic-q-a/58652/additional-questions-to-nrf52832-errata-220-clearification and https://devzone.nordicsemi...
Hello,
iam using nrf52832 wiht nrf5 sdk17. we built our application code on ble_app_hids_mouse, now i would like to know how to carefully isolate this file from entire sdk...
We appear to be getting a "z_arm_secure_fault" after the call to "flash_read", trying to access what appears to be any area of flash memory using tag v1.3.0. This call, including...
I'm running the SAADC example from the nRF5_SDK_17.0.0_9d13099 SDK. I didn't add any modification to the code. except for replacing NRF_LOG with printf.
The power supply...
