Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I have looked at and used the following references:
https://devzone.nordicsemi.com/f/nordic-q-a/47484/ble_gap_evt_scan_req_report-not-working
https://devzone.nordicsemi...
Is it possible to implement open thread cli using 16 castellated pins of BT840 ?? I can change the uart pin by rebuilding the open thread libraries ,
Can I avoid using...
Dear all,
In our project we are using "nrf52840" IC is used. We need to check its strength in various physical layer by loading the " Direct mode code ".
We have sucessfully...
Hi !
I need to develop a BLE communication link between a smartphone (Android first, iOS after) and the BL654 Laird platform (based on nRF52840).
I found multiples strategies...
i am developing a bike power meter and designed my own hardware.
From software point of view I used the Ant+ bikepowermeter example from Nordic.
So far my status is, ...
To the kind attention of Nordic support team,
Could you please help me finding documentation about the subject I mentioned?
Let's suppose we have got a peripheral and...
Hello,
I am working on ble_app_uart example on nRF52840DK.
I am using one switch (gpio) for advertising_switch() function. It means on changing the position of the switch...
Hi,
Would you please tell me how can I dump a memory and save into a file in keil uVersion 5.24?
For example: I want to read the flash memory 0x00000000 to 0x00010000...
There is an option to 'Clone device's services':
A message pops up briefly to say that it's done it:
But it doesn't say where it's put it, and I can't see any...
Dear all,
I have picked the Ruuvi project : https://github.com/ruuvi/ruuvi.firmware.c and change the configuration to adapt with nordic dongle.
But after flashing, my...
Hi,
I am evaluating LC example, I am using an occupancy sensor. So whenever there's an occupancy it's detecting and turning the lights ON. But even when there's occupancy...
Hi,
I have created an eclipse based makefile project for nrf51802 module.
The sdk version that i am using is 12.3.0, and softdevice S130 .
Taking reference of ble_app_uart...
HW setup is my boart connected to a windows10 PC with an uart link.
I tried secure_bootloader_pca10100_uart_ses_nRF5SDKThreadv4.1.0.zip example, with some modification for...
Hi All,
I followed this article and got eclipse to work. I can use debugger, single-step, place a breakpoint. All good.
I noticed that disassembly window shows opcodes...
Hello,
I am working on a project that uses Azure as a cloud IoT provider and the NRF9160 as a gateway-like device which is supposed to make simultaneous connections to up...
