I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
There is now a TI CC2451 Bluetooth module as a reference. Using nRF connect to monitor the log content, it is found that when the mobile phone is connected to Bluetooth and...
Hi everyone, I have a question about GPIOTE.
What happens if for example, GPIOTE is used to configure a pin to detect a low to high transition, but the pin is already...
Hello
I have a problem with restarting advertising after disconnect event.
There are two scenarios:
In this case everything works fine:
I start advertising
...
Hello,
I started with the template app and tried to do two things on a nRF52832 using Segger Studio:
1) advertise custom service
2) use Application Timer and App Scheduler...
Cannot connect to nRF52840DK board using nRF Connect Bluetooth Low Energy app on Linux (Ubuntu 18.04 LTS). When I choose "Select Device" and choose my board, I get:
"Validating...
We have custom developed board using nrf52832. When I run the example program developed in SDK15.0.0 with Soft device S132 V6.1.1, no issue noticed in running debug mode ...
For creating a Bluetooth mesh Hub that will communicate to the Azure IoT server, which should be the best suitable ethernet board for connecting with the nRF 52 DK?
This is a bug report for SDK v15.3.
Once a GPIOTE interrupt is enabled for a pin, nrfx_gpiote_in_event_enable(pin, false) will not disable it. This appears to be an issue...
Hi,
I wanted to design a custom development board based on nRF52832 SoC. I will go with the exact schematic diagram which was given in Nordic supporting site ( https:...
I'm looking for some additional information about the Assisted GPS functionality in the nRF91.
Exactly what is it?
How does it work?
Is it available with the current...
Hi,
I have an application that does HTTP requests to a backend server. I'm now working on implementing TLS for encryption of the data.
Are there any examples of doing...
Hello everyone,
we are developing a bluetooth application based on the relay example included in SDK 14.0.0. We have already developed our own services and characteristics...
Hi,
I've been searching for a LSM9DS1 driver compatible with the nRF5 SDK >= 14.0 but I couldn't find any which uses the nrf_drv_twi so I started to write my own but it...
Hi All,
I'm working on minimizing power when transmitting a small message between two nRF52832 boards. I'm also trying to maximize range so sensitivity is important.
I...
Please ignore, this is test post. The SES project in Thingy:52 SDK seems to be broken, I get a lot of error trying to compile. What can I do to fix it?
