Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello! I am having issues dfu from the huawei p30 lite. with nrf51. Tried with nrf connect and nrf toolbox.
Dfu progress stops at 2-3% when uploading. Error Remote dfu error...
I am unable to connect the nRF9160DK to the cellular network.
I have gone through the "Get started guide" (working in Linux) and I have been able to install the SDK. I have...
Hi, we have faced with the same issue as many nRF52 users, debug interface (DIF) will stay active after flashing and high (~3mA) continuous current remains, Power cycle will...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
In BLE peripheral example ‘ble_app_template’, it is for doing Advertisement...
hi... folks
I am working on multilink central example, i have modified this example to multi link central uart ,where i can able to connect to multiple peripheral to a single...
Hi,
I am using NRF51822(PCA10028) ble_app_uart example , I need to change the name of the BLE device during Advertising and store the name in Flash so that when ever the...
Hello,
I am trying to establish a network to send data over the boards.
I tried using examples in Ble_central and Ble_peripheral, but in those examples they would stay...
Using the esb tx fifo, it appears to change the ESB_MODE from PTX to PRX, and changes the esb channel to some other value. Is there any way to setup the radio so that it doesn...
Hello,
I am working with nrf52840. I have read how the SAADC example works at https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v13.0.0%2Fnrf_dev_saadc_example...
Hi everyone, I'm having trouble deciding on the "best" / "most sane" way to interface two I2C sensors with the nRF5832. Both sensors are on the same I2C bus. The first sensor...
Hi Bro
I have a project need to use BLE + ESB Concurrently, actually I have did it in my previous project
but seems it has problem in new SDK
In my old project: SDK11...
I'm using the nRF52 DK (with an updated firmware) to program an external target (using the "Debug out" connector). It looks like the programming speed is limited to 1MHz:...
HI,
I am seeking help in getting the only peripheral code from the ble_app_mtu_throughput. Actually, I want to use the only peripheral code in my and want to use the maximum...
I have multiple sensors. I would like to ask if there is support for linking 4 or even 4 Bluetooth devices at a time.
My ultimate goal is to connect 4 or more Bluetooth...
