Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
I'm trying to do a low power sleep of 1s directly after a device reset, i.e. in Reset_Handler().
During this stage, my application does not allow any interrupts.
So my...
Hello DevZone community!
I'm having trouble debugging more than one board at the same time in a Linux development environment.
For a single board, I can debug either...
hello, i am using nrf52 dk .I was testing example twi scanner.I want to read slave address.So i am using twi scanner example but i got error message as follow:
TWI:INFO...
Hi, I'm new here and I use nRF52832 (pca10040), I was wondering if it is possible to change a function in C / C ++ language during the runtime, that is, my idea is whenever...
Hi,
I had a problem using your (nRf's) implementation of block device with my flash memory (I think that exact model is not relevant here). I'm using SDK 15.2 with NRF52840...
Hi,
Do you have a declaration of conformity for the chipset nRF52832 ?
I need this document to justify to my laboratory the conformity of the Bluetooth module to the standard...
hi,
I have some questions, please help me solve these questions. ( I use SDK 15.2.0 and nRF52832)
1. my customer ask how many central bonded with one nrf52? (my project...
Hello,
I am trying to send data from my light switch mesh client (nRF52840) to my gateway, the nRF9160 using UART. I added the UART functionality to the light switch client...
Hello there,
I followed all the steps in the following link:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52%2Fdita%2Fnrf52%2Fdevelopment...
My device (nrf52832) has two signals triggering GPIOTE interrupts. I need to be as low power as possible, so both are setup to not use hi accuracy, making them share the PORT...
i need a help
As mentioned in this thread
https://devzone.nordicsemi.com/f/nordic-q-a/18512/directed-advertising-with-pre-shared-irk
in need to do directed advertising...
Hi,
We want to measure our external custom board which is not based on nRF52 chip. That board has current consumption header and it's chip draws maximum current of 60mA...
Hi:
I find a odd question when i use SES to develop nRF52832, ESB protocol is using and i need to config some different slaves with same code except the pipe num, i define...
Hello,
In my current zigbee project I have a sensor end device which should sleep when possible. I am handling the ZB_COMMON_SIGNAL_CAN_SLEEP event and have added zb_set_rx_on_when_idle...
Hi,
I am using NRF52 SDK version 15.3, Segger Embedded Studio.
I am using the ble_app_beacon example in examples/ble_peripheral, I have programmed 2 devices with the...
