I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I'm attempting to flash program a Nina B112 Bluetooth Module (from Ublox), which is built uppon a NRF52832 board and i'm attaching this module to a custom board.
I...
Hello,
I'm building BLE preipheral and central devices for transmiting voice signal (best audio quality is not very important requirement) from peripheral to central. I...
Hi All,
We are in evaluation phase of a project where in our battery powered device would use nrF52840 MCU and communicate to the mobile phone over BLE (say about 5x times...
I am working on nrf52832 and sdk11. I want to store my accelerometer and gyroscope data into external memory.Does anyone have code of it? or any one having .c and .h file...
HI, I am using nrf52832 soc and i develop our own module. i need to create a mesh network within the device.
I am using segger embedded studio 3.34 (windows 10) and SDK...
I am new to BLE and want to learn what options and methods I have available to alter the advertisement package. Is it possible to include a floating point value, that could...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
Hi,
I am using pca10040 board of nrf52 dk. I am running battery level measurement code on board but whenever I observed values on serial monitor it shows garbage values...
Dear Developers and Members of the Forum
I have an Apple Macbook 6.1 (Late 2009) that has a built in Bluetooth Chip (Broadcom 2.1+EDR) and I want to use Xiaomi Mi Portable...
Hi,
I am trying to develop low power beacon on nrf52.
Which example should I base on?
I am trying example ble_app_blinky on PCA10040, and I am getting close to 1 mA...
Hi,
I have implemented the Master serial DFU code to update application and SD file. I'm following DFU packet send sequence. Ping, inti packet, FW packet.
I'm framing...
Hi,
I need to develop code for the custom board test, in which I need to enter the <channel> and it <power> value & then begin start/stop the continuous transmit the radio...
Hello,
Recently I purchased a nrf52840 Dongle to use it with nrfConnect for Windows.
I use nrfConnect 2.6.1. When I insert my Dongle in a USB port the LED starts pulsating...
Dear Sir,
We need a sample code for UARTE nRF52832 using EasyDMA. This sample code should drive our UARTE port using in BLE to UART mode. We could not find it by asking...
