I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello!
I'm having a problem and a hard time trying to understand what's wrong. Currently, I'm using the SDK 14.2.0, SD 5.0.0 and Segger on macOS 10.14.2.
I'm using the...
Hello,
I have a product using NUS profile and plan to update it to support connection from multiple phone
Do you recommend to start from Multiperipheral example and...
if i use this code to send data,i sometimes miss data..
do { err_code = ble_nus_string_send(&m_nus, (uint8_t*)data, &data_len); if (( err_code != NRF_ERROR_INVALID_STATE...
I have nrfutil version 5.0.0. I run this command:
nrfutil pkg generate --hw-version 52 --sd-req 0xA8,0xAF,0xB7 --application-version 2 --application ./nrf5/Debug/nrf5.ihex...
Hello! We are trying to use Nordic AndroidScannerCompatLibrary in our Android application to scan BLE devices and measure its RSSI level. BLE devices is mounted on ceiling...
Hello there,
I would like to read the data I sent through a WS2812b LED string. I drove it using I2S. Upon reading it, seems like it is not a good idea to read it using...
Not sure what I did to cause this, but my nRF52840 no longer works. I searched for solutions and came across:
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52...
Hi,
I am wandering if it would be possible at all, to wrap a quarter wave antenna printed on flex pcb around a cylindrical battery (LiFePo4)?
Would the radiation be...
Hello,
Information:
SEGGER Embedded studio Studio v412
Windows 10
nRF52832 on a development board.
We are attempting to merge an application with a bootloader...
I have read that the nrf51822 is not supported anymore in the examples of SDK's older then V12.
Does the nrf51 completly not work anymore with newer SDK's or are only the...
I have my system working with softdevice compiled in but not enabled. System communicates with external chip using SPIM peripheral, everything is working fine until I enable...
Hi,
I have my custom board wired to the nRF52 development board. I am using SDK 15 and softdevice 132 for this. I am trying to set up SAADC to measure adc data on Analog...
Hi,
I'm only seeing the GPS_SIM driver in the nRF Connect SDK. Is there any driver to enable any evaluation of the nrf9160 on chip GPS anywhere?
Regards,
Kilian
