I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Bluetooth Mesh specification uses the concept of composite models that "extend" other models. I am having trouble understanding the scope of this concept within the Mesh specification...
For nRF52840 (Rigado BMD-340), SDK 15.0.0, custom board:
I'm trying to implement nrfx_uart directly to communicate to another microcontroller. I've configured it for blocking...
Hi all
I'm using the NFCT peripheral of the nRF52832 Revision 1 and I'm facing the following issue:
When the reader sends the SLP_REQ, the NFCT receives an incomplete...
Hi, there
I want to remove the bond in current time service example, because the bond process make me less convenient when I debug. so I changed the code in peer_manager_init...
Hi using dev kit pca10040 and sdk 14.2.
I'm trying to use the dev kit buttons to stub out an ANT+ bike speed sensor. Essentially I just need a way to provide a speed reading...
Hello, i am using ble_app_uart example. i am trying to send A to Z from ble to uart. Has i noticed, it is transferring 20 characters at a time. to make sure that i add print...
I am using nRF5_SDK_15.2.0_9412b96. I have application data that accumulate in flash but can be thrown away before re-flashing new app image. I am thinking about instead of...
Hi,
I configured nrf_ble_qwr to use 256 byte long buffer in my BLE peripheral. I registered my value handles (2) which I want to support long writes using nrf_ble_qwr_attr_register...
Hi Folks,
I'm new at using the nRF52832 chip. I recently was handed a 3rd party board to evaluate and up until today I was able to use the nRF52 Development Kit to act...
Hi,
I am working on "nRf52832 - PC10040" based ISP1507/. I have already adapted the peripheral/spi example of SDK 15.0.0 to my needs. Now, I want to merge this spi example...
Hello,
With Segger ES I am able to compile and run the Blinky example (pca10040, S132) from the nRF5 SDK without any issues, it loads on my nRF52 DK board on and it shows...
Hi,
I'm working on a project where I need to collect and process analog data coming from high speed sensor measurements. The data needs to be read at a speed of 25k samples...
Hi,
I am trying to convert the string from ctime to a struct but i always get garbage values if i use "uint8_t". But i can get correct values if i use "int" datatype....
Hello Nordic
Bluetooth SIG had released their new bluetooth core specification 5.1 with new feature is " Direction Finding ".
I know that all nrf52 now support BLE 5.0...
