Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
hi，all
i got the nrf52832 dk and run the ble_app_uart example ,
but i found nothing output in jlink rtt viewer after called the NRF_LOG_INFO("UART Start!") ,
so could...
Hi.
I did the secure bootloader DFU. I attained step 8 in document .
I instal softdevice and secure bootloader to flash nRF52832. After make the ble_app_buttonless_dfu...
Routing the DCC pin on the nRF52832 with the chip scale package is pretty tough. The bump is surrounded on all sides by other bumps, so I don't have room for a via in the...
Hello,
I'm using nRF Connect V2.6.1 on Windows 10, I launch " Bluetooth Low Energy V2.2.0 " that uses PCA10059 Dongle as central.
Also, I have developed a peripheral application...
There are 12 LEDs which are connected using shift register HC595 ,the module used is nrf51822(bluetooth module). I want the LEDs to go off after 3 seconds interval. My code...
Hi there,
We are having issues with our boards that uses nrf52832 chip. Our first built had this chip and everything was working fine. We built a second batch and all boards...
Hi,
In nRF52832 datasheet I found that it is having internal oscillators, like 32.768Khz RC oscillator and 64MHz RC oscillator. If it is having internal oscillators what...
Hello
Most of the time we shall use the BT TX 0dBm. In special cases when we want to increase the communication distance we may select the 8dBm mode.
For RF type approval...
I am implementing long read with authorization in the server (peripheral). I have a characteristic with vlen = 1 and maxlen = 300. ATT_MTU = 23.
gatts_attr_md.vlen = true;...
Hi,
I added nRF5_SDK_15.2.0_9412b96\modules\nrfx\drivers\src\nrfx_timer.c to my project. In sdk_config.h I have:
#define NRFX_TIMER_ENABLED 1 #define NRFX_TIMER1_ENABLED...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96,PC is windows 10
I want to use the DFU to update my file,but I find that only the Init packet is signatured...
I am trying to integrate SPS30 sensor to nRF52 DK using Segger Embedded Studio. The sensor fails to initialise and the program keeps getting stuck at NRF_BREAKPOINT_COND at...
Hi,
In nRF24 / nRF51 , the product sheet have the 20dB Bandwidth for Modulated Carrier (2Mbps) parameter.
However , i could not find at nRF52832 ps.
Did it the same...
