Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hi,
I am working on developing a consumer product. I need to provide some security to product in the sense that not everyone can connect to the BLE of the product. For example...
Hi All
I have a system with two PCA10040 boards both running with SD version s132_nrf52_6.1.0. The application is build with SDK version 15.2.
I have implemented a peripheral...
I use ble_app_hrs_rscs_relay to build a node which has both central and peripheral roles. I can do scan and adv, but when I add eddystone functions "nrf_ble_es_init(on_es_evt...
Hi,
I want to develop central code to discover services of 3rd party device and to discover their services and read/write characteristics.
As seen many examples from...
Hello,
I am working on NRF52840 DK for a project on Bluetooth Mesh. Using Segger Embedded Studio for Building and debugging.
Basically i am trying to run the examplecode...
I'm writing two 32 bit words. I've verified that the source and destination addresses are word aligned (the UICR address is 0x10001088 and the source address is 2000200C)...
hi.....
i have merged the two programs ble_uart and twi sensor ......in nrf52832 ...segger15.2
i have attached all c files and h files ...... no errors ...when flashing...
Application on NRF52DK running fine average current 2uA. After installing hard and software for the PPK power profiling kit the application draws 8 mA!
Application functions...
Hi guys,
I have a board with STM32 (mbed os) and NRF52832 connected using UART lines.
STM32 has a internet connection and NRF52832 has a bootloader and DFU service.
...
I want to send sensor data from one node to other using access_model_reliable_publish() method, but my data is too large and I'm not able to send large data. What is the maximum...
Hello,
I'm using the TWI example mentioned in the subject line and I'm trying to get the TWI signals out of my demo board (Rigado BMD-350 Evaluation board).
Am I right...
hi everyone
I have BMD-300 Series Evaluation kit featuring the nRF52832 and dongle(nrf52840).
And I`m using ubuntu via Virtual Box
I refer 'pc-ble-driver' and follow...
Hello.
I am trying to build something like this in the picture below:
so my guess is that I need mesh functionality.
So my initial questions are.
Are there any...
Hi Sir
I start development form uart cli example (uart0), now nrf52840 module will connect an uart peripheral device by uart1, so two uarts would be used.
My goal is to...
