Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Subject: Query: Interfacing OLED SSD1306 with nRF52832 on Zephyr
Dear Zephyr Dev Zone Community,
I hope this message finds you well. I am currently working on a project...
Hello! The S140 7.3.0 SoftDevice docs say it requires 0x27000 of flash, but the SoftDevice hex only occupies 0x26634 bytes. This leaves 2508 bytes of hopefully unused flash...
Hello, I'm trying to confirm whether the front-end module (FEM) is actually active in my application. Here is a summary of what I have done so far:
Updated prj.conf...
I followed the example described in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.2.0/nrf/ug_nrf52_developing.html#fota-updates
and the loaded the SMP Server example...
Hallo,
currently I test several options in regarding the use of advertising. I have a few nRF52840-DK and use Zephyr 2.7-99 and ncs. I have a question regarding combined...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
In our application, we provide internet connectivity to the WT02C40C module via a mobile...
Hi,
I have a makefile generating an elf and then a hex and bin file for a nrf52 project. Now I builded up a zip file for bootloading. Which works as well.
Now in our CI...
We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version.
We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
I want change toolchains, so when i open nrfconnect terminal I can use my own west command. I've read link , link and link
Option in the picture lets me install or open...
Hi,
There were GPIO /SPI Interface headers are given on NRF21540 EK .now how we can connect RF input to TRX pin of NRF21540.
please provide the Understanding of RF input...
Hi
We are looking into connecting an external GNSS antenna to the Thingy91x board. The drawings metion 2 ports J1 and J2 but can't find anything in the docs if these are...
Hi, I am currently outputting some audio (1000hz sine wave) via audio_i2s_blk_comp_cb_register and audio_i2s_set_next_buf (from audio_i2s.h ) through the line out audio jack...
Good morning, I am trying to send data via BLE from a custom board (with the nRF52840 microcontroller) that has sensors, to an evaluation board nRF52840 PCA10056. To do this...
