Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I have tried to used the function below.but it will make my key interrupt disable when i set gpiote_ch_id to 0 .My key is in PIN 0.11.
So I want to know the meaning of gpiote_ch_id...
Hi,
I would like to know if there is a footprint difference between NRF52810-QFAA-R and NRF52832-QFAA-R in other term, can I use both with the footpriint of NRF52810-QFAA...
Hi! I have mentioned this already 9 month ago in another ticket ( https://devzone.nordicsemi.com/f/nordic-q-a/75331/dfu-upgrade-of-only-bootloader-not-softdevice ) but it...
Hi ,
the nrf25840 data states regarding temperature sensor's accuracy: To achieve the measurement accuracy stated in the electrical specification, the crystal oscillator...
Hi, I use two nRF52840 DK for testing purposes for over 1.5 years now. Suddenly, yesterday the BLE module in one of the DK's stopped working. Just like that. Same functional...
Hellow
We are in trouble. Please tell me what to do.
The input range of the SAADC is not as expected.
I use: ・nrf52840 ・VDD=3.3V by Regulator ・nRF5_SDK_17.1.0 ・Sample...
The example ble_app_uart is working fine (i.e. I get NRF_LOG_INFO from gatt_evt_handler), but my code doesn't. I've checked the diff between them and tried adding all diffs...
Hi All,
I am using nRF52 DK board & nRF5_SDK_17.1.0 for Development(Emulated Project for nRF52805), My application needs creation of multiple service and multiple characteristics...
I bought a handful of nrf52840-Dongle boards, with the intention of developing an application on one "dev" board and then flashing it through the Open Bootloader on the others...
hi am working on DFU- OTA on nRF52833. In one of the query I found the method for to evaluate DFU- OTA on nRf52833 , am able to do that ,after connected to the Bluetooth I...
Hello,
I am new to Nordic. Earlier I was using Cypress controllers CYBT343026-01. As per nRF documentation, I believe once the controller goes into a deep sleep mode, I...
Hi, devzone!
I'm trying to use a timer to periodically change the digital output but it seems that the handler function is not called.
The whole code is based on the...
Hello!
For a project, I am relying on RSSI data from the development kit nRF52832. The problem is that the data I get is in dBm (I assume?), that is values like -30, -50...
Hi,
We are designing a board that is controlled by a NRF52840 and that will use a NRF21540 (FEM) to enhance its radio link budget.
We will use the FEM with diversity antenna...
Hi,
The DFU(reuse ota code) partition configuration file I got from your technical support is as follows,It divides Flash（1024K） into the following regions：mcuboot(48K)...
