I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I'm using Android DFU library 1.11.1 and occasionally I see "E/DfuBaseService: Connection state change error: 133 newState: 0" errors. It appears they happen when the initial...
When using nRF Connect SDK v1.6.1, a BLE peripheral that supports 2 simultaneous connections could be created by including these lines in prj.conf. These lines set the Link...
Hi,
this is kind of continuation of my previous ticket . After solving it the last time I thought that I don't need wait_for_flash_ready() function as it caused some problems...
I just buy nRF5340.
I install nRF Connect in my PC.
and install bluetooth app.
I just select my pdk.
log show
INFO Connected to device with serial number: 000960119975...
Hi,
I have the following 2 scenarios:
Scenario 1: I create an image with nrfutil containing SD, App and debug bootloader. I flash this image and it works. Then I change...
We have nrf5340pdk kit we are trying to flash code via nrf connect or Segger studio but firmware is not flash and when we powered up the pdk it's showing three port can you...
I'm using Visual Studio 1.7.1 on Windows 10 machine. With an nrf916DK.
I'm trying to learn about the shell and all seems to be working fine, based on what I've found in...
I'm trying to work with Kismet's nrf51822 plugin that would allow kismet to read the nRF BLE sniffer 4.1.0 the same way Wireshark does. Alas, theirs is C based and I don't...
Dear friend,
Based on the following conditions: SDK: 15.3 Target board: nRF52840-DK Example: \examples\ble_peripheral\ble_app_ancs_c ios version: 12.5.5 Do the following...
Hello,
I have successfully achieved the modem delta firmware update from mfw_nrf9160_1.2.7 to mfw_nrf9160_1.2.7-FOTA-TEST, vice-versa with sample code. But when it comes...
Dear support
Just started to learning following the tutorial here - https://devzone.nordicsemi.com/nordic/b/archives/posts/nrf-connect-sdk-tutorial---part-1-ncs-v1-3-0#h769sk6kqovea15p99jn16lstat1dtpuuw...
Recently I purchased nRF9160 DK and I have a Vodafone Idea SIM (active). I followed the instructions precisely as per the Nordic infocenter but I am not able to connect my...
Hello
nRF52840 is easy to know pin number,
but nRF5340 no pin map,i can't read the pin diagram.
don't know where the pin corresponds to.
thanks
Best R...
Hi,
I managed to have the fat_fs sample to work.
Now i would like to be able to write and read files, onto the SD-CARD, that a PC will understand, it seems to needs...
